Upright X Series Скачать руководство пользователя страница 17

Страница: 17 / 164

Page 2-5

Operation and Specifications

2.3 - Operation

X Series Work Platform

TEERING

1. Turn the Lift/Drive switch to DRIVE.

2. Engage the Interlock Switch, push the Steering Switch RIGHT or LEFT to turn the wheels in

the desired direction. Observe the tires while operating the machine to ensure proper direc-
tion.

NOTE:

Steering is not self-centering. Wheels must be returned to the straight ahead position by operating

the Steering Switch.

LEVATING

THE

LATFORM

1. Select a firm, level surface.

2. Turn the Lift/Drive Switch to LIFT.

3. Engage the Interlock Switch and push the Control Handle forward.

4. If the machine is not level, the tilt alarm will sound and the machine will not lift or drive. If the

tilt alarm sounds, the platform must be lowered and the machine moved to a firm,
level surface before attempting to re-elevate the platform.

RAVEL

WITH

ORK

LATFORM

LEVATED

NOTE:

The machine will travel at reduced speed when the platform is elevated.

1. Check that the route is clear of obstacles (persons, obstructions, holes, drop-offs, bumps,

and debris), is level, and capable of supporting the wheel loads.

2. Check clearances above, below and to the sides of the platform.

3. Turn the Lift/Drive Switch to DRIVE.

4. Engage the Interlock Switch and move the Control Handle to FORWARD or REVERSE to

travel in the desired direction. The speed of the machine will vary depending on how far from
center the Control Handle is moved.

5. If the machine is not level, the tilt alarm will sound and the machine will not lift or drive. If the

tilt alarm sounds, the platform must be lowered and the machine moved to a firm,
level surface before attempting to re-elevate the platform.

OWERING

THE

LATFORM

1. Turn the Lift/Drive Switch to LIFT.

2. Engage the Interlock Switch and pull back on the Control Handle to lower the platform.

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды