background image

© UPLIFT Desk

 • 800-349-3839 • [email protected] • upliftdesk.com

2

0.25”

2.4”

3.9”

1.9’’

0.4”

1.7’’

Step 4 (Clamp Method)

A.  Using the 6mm Allen Wrench, adjust both bolts on 

the bottom of the Lower Clamp so that the open-
ing is wide enough to accommodate the thickness 
of the desktop and Clamp Plate.

B.  Place the outer holes of the Clamp Plate onto the 

tips of the bolts as shown.

C.  Slide the assembly onto the back of the desk-

top, then tighten the bolts using the 6mm Allen 
Wrench. Alternate from one bolt to the other, to 

allow the Clamp Plate to rise evenly before finally 

tightening to the desktop.

D. If you chose the Clamp Method for mounting, 

please skip the Bolt-Through Method Steps 5-7 
and proceed with Step 8.

Step 6 (Bolt-Through Method)

A.  From the top of the Upper Base Plate (the side 

opposite from the countersunk holes), insert 
both Long Bolts through the square holes until 

the square shank of each Bolt fits into the Plate’s 

square holes.

B.  Then, align the Upper Base Plate with the bottom 

of the base in the orientation shown and attach 
it using the four M6x12 Flathead Screws and the 
4mm Allen Wrench.

Bolt-Through Method

Step 5 (Bolt-Through Method)

The Bolt-Through Method utilizes either one or two 
holes in your desktop to fasten to it.

One hole:

 Minimum 2.4’’ and maximum 3.9’’ in diame

-

ter. Both bolts will fit through a hole within this range.

Two holes:

  Minimum  0.4’’  and  maximum  of  1.7” 

spaced 1.9” apart at centers. One bolt will fit through 

each hole.
Using a grommet hole that is already in your desktop 
is acceptable, or you can drill holes at these measure-
ments anywhere on your desktop.

Содержание UDA126









Отзывы: