Upland 207P Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 33

Upland 207P Скачать руководство пользователя страница 17

Never use gasoline, acetone, paint thinner or any
other highly flammable, volatile substance.

Close the
combustion air
control damper by
pushing towards the
stove.

The combustion air control damper is
located to the upper right of the Controller

You then light the pellets, close the door, and adjust
the air control damper to spread the flame.

The stove will enter the Warmup Mode. During this
period the Fuel Sensor is disabled. The Controller will
alert you every ten minutes while the stove is in this
mode.

Two or three ten minute cycles is typical to

bring the stove up to temperature.

Do not leave the stove unattended until it is up to
operating temperature and the Controller
switches to operating mode. At that time you can
then adjust heat output setting.

When the stove reaches operating temperature, the
Heat Level will go to the last set point.

«
...
15
16
17
18
19
...
»

Содержание 207P


































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды