Upland 207P Скачать руководство пользователя | Manualshive

Страница: 1 / 33

background image

INSTALLATION

AND OPERATION

UPLAND® 207 PELLET STOVE

Thank you purchasing our stove. With proper
installation, operation, and maintenance this stove
will provide you with warmth and hearth enjoyment
for decades. Please take the time to review the
proper installation and operating procedures.

This is a natural draft pellet stove. That is not
common. However, it is part of the design that
provides an awesome fire view, trouble free
operation, and great flexibility in the quality of the
pellets that you may burn.

CRITICAL - THE VENTING:

The Upland 207P Pellet

Stove must be installed following the National Fire
Protection Agency 211 and ASTM 1059 guidelines
for a natural draft solid fuel appliance. The flue must
clear the roof line and rise two feet above any portion
of the roof that is within ten feet. That is standard for
a wood stove or coal stove. (This type of installation
eliminates most back draft and shut down problems
and keeps the side of your home free of hydrocarbon
deposits.)

If you are replacing another solid fuel heater and
connecting to an existing solid fuel chimney this is
not an issue if your original installation is up to code.
You should already be in compliance. A standard

1
2
3
...
»

Содержание 207P


































Отзывы:

Нет отзывов

Похожие инструкции для 207P

Бренд: Harman Страницы: 35

Бренд: Harman Страницы: 42

Бренд: Harman Страницы: 36

Advance Freestanding Pellet Stove

Бренд: Harman Страницы: 44

Advance Pellet Stove

Бренд: Harman Страницы: 7

PHAROS INTERIOR

Бренд: Harrie Leenders Страницы: 56

Бренд: Harrie Leenders Страницы: 22

Бренд: Jøtul Страницы: 32

Studio Stove 14

Бренд: Warmington Страницы: 16

Бренд: Olimpia splendid Страницы: 8

Бренд: Vendor Development Group Страницы: 8

Бренд: Nibe Страницы: 4

Бренд: KASTOR Страницы: 69

Бренд: Stanley Страницы: 24

Бренд: Aarrow Страницы: 28

Бренд: Morso Страницы: 12

2B Classic 2020

Бренд: Morsø Страницы: 631

Бренд: Cadel Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды