Univex RDRE Series Скачать руководство пользователя страница 20

Страница: 20 / 44

RDRE

- electric version - gas version - Page 18

Cart

Insertion

- Set the time for the humidification cycle.

- Completely open the door.

- Check that the steam extractor starts working.

- Push the cart into the oven until the upper bearing of the cart enters the housing of the hook.

- Close again, and turn the door handle clockwise until it is locked horizontally.

Extraction

- An acoustic signal will advise you that the set cooking time has expired.

- Begin taking the products out of the oven as follows:

- Release the door, and leave it ajar for a few moments. This will allow any residual steam to be extracted.

- Now open the door completely. Using heat resistant gloves, extract the cart.

- Close again, and turn the door handle clockwise until it is locked horizontally.

INSTRUCTIONS FOR USE
SAFETY INSTRUCTIONS FOR THE USER

Attention!



Only after completing all connections, the unit is ready for commissioning.



The unit can be safely operated only if the following instructions are adhered to.



The user may use this appliance only after he has been properly instructed on its use and operation.



Coverings or parts of the unit which can only be removed with the aid of a tool must absolutely not be

removed.



The unit must be monitored while in use.



During operation, the door becomes hot. Be very careful with it.



Be very careful when opening the door during operation or when the unit is hot, as hot vapours may be

released by it!



Protect the unit from freezing temperatures.



All work concerning installation or repair of the unit are to be performed by qualified personnel in

compliance with current standards.

At least once a year, have the unit checked by qualified personnel from the manufacturer. For this

purpose we suggest stipulating a service contract.



The unit must be cleaned on a daily basis.



The unit is not protected against splashes of water. Therefore, do not use direct or pressurized jets of

water



Note:

The noise level at in the workplace is less than 70 dB (A). This information is required for certain

national safety standards.

Delayed start:

allows the operator to perform start-up and hence the pre-heating phase at a certain time by

setting the day and time using the programming knob. Enter the menu to set in order the day of the week, start-

up time and enabling.

Содержание RDRE Series













































Результаты поиска

Содержание RDRE Series

Отзывы:

Похожие инструкции для RDRE Series

Бренды по названию

Популярные бренды

Univex RDRE Series, Инструкция по эксплуатации

Результаты поиска

Содержание RDRE Series

Отзывы:

Похожие инструкции для RDRE Series

Бренды по названию

Популярные бренды