background image

Manufacturer/Supplier

Product Type

RPM

Cycles Per Min

Tel No

Fax No

(01494) 883300

(01494) 883237

Model No/Nos

Serial No

Product Nett Weight

lbs
Kg

Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins

M/M

Ft

M

Foreseen Use of the Tool

This tool is designed for the purpose of the removal of gaskets,
gasket residue, trim that has been bonded to vehicles etc.,
adhesive residue, decals, paint and rust etc. Do not use the tool
for any other purpose than that for which it is designed. Do not
modify the tool for any other use or for its use as a scraper
without first consulting the manufacturer or an authorised
distributor

Putting Into Service

Air Supply

Use a clean lubricated air supply
that will give a measured air
pressure at the tool of 90
p.s.i./6.3 bar when the tool is
running with the trigger fully
depressed. Use recommended
hose size and length. It is
recommended that the tool is
connected to the air supply as

Work Stations

The tool should only be used as a handheld, hand operated tool.
It is always recommended that the tool is used when standing on
a solid floor.  It can be used in other positions but before any such
use, the operator must be in a secure position having a firm grip
and footing and be aware of a reaction force on the hand as result
of the tool doing work.

No

Air Pressure

Recommended Working

6.3

bar

90

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

7.0

bar

100

PSI

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

 

Use - Safety Boots
Use - Breathing Masks
Use - Ear Protectors

Yes

Page No 1

Gasket Scraper

UT079 (HP079)

0.71

3/8

10

30

10

Includes - Foreseen Use, Work Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules

Operator Instructions

Important

Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.

Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY

Vibration Level

Test Method 

Tested in accordance with ISO

standards 8662/1

25.7

Metres / Sec²

1.56

4,800

N/A

Noise Level

Sound Pressure Level 86.0 dB(A)

Test Method

 Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Sound Power Level 97.4 dB(A)

shown in figure 1. Do not connect the tool to the air line system
without incorporating an easy to reach and operate air shut off
valve. The air supply should be lubricated. It is strongly
recommended that an air filter, regulator, lubricator (FRL) is used
as shown in Figure 1 as this will supply clean, lubricated air at the
correct pressure to the tool. Details of such equipment can be
obtained from your supplier. If such equipment is not used then
the tool should be lubricated by shutting off the air supply to the
tool, depressurising the line by pressing the trigger on the tool.
Disconnect the air line and pour into the intake bushing a
teaspoonful (5ml) of a suitable pneumatic motor lubricating oil
preferably incorporating a rust inhibitor. Reconnect tool to air
supply and run tool slowly for a few seconds to allow air to
circulate the oil. If tool is used frequently lubricate on daily basis
and if tool starts to slow or lose power.
It is recommended that the air pressure at the tool whilst the tool
is running is 90 p.s.i./6.3 bar. The tool can run at lower and
higher pressures with the maximum permitted working air
pressure of 100 p.s.i./7.0 bar.

Содержание UT079

Страница 1: ...71 3 8 10 30 10 Includes Foreseen Use Work Stations Putting Into Service Operating Dismantling Assembly and Safety Rules Operator Instructions Important Read these instructions carefully before installing operating servicing or repairing this tool Keep these instructions in a safe accessible place Universal Air Tool Company Limited Unit 8 Lane End Industrial Park High Wycombe Bucks HP14 3BY Vibrat...

Страница 2: ...only compressed air at the recommended conditions 5 If the tool appears to malfunction remove from use immediately and arrange for service and repair 6 If the tool is used with a balancer or other support device ensure that it is fixed securely 7 Always keep hands away from the working attachment fitted to the tool 8 The tool is not electrically insulated Never use the tool if there is any chance ...

Страница 3: ...76050 Roll Pin 2 8 1010S Air Regulator 9 13104 Upper Valve 10 13105 Middle Valve 11 13106 Lower Valve 12 13107 Valve Disc 13 131090 Cylinder Assembly 14 13108 Piston 15 13111 Blade Holder 16 13112 Lock Screw 2 17 13120 Scraping Blade Standard 18 13121 Scraping Blade Optional 19 13122 Scraping Blade Optional 20 13123 Scraping Blade Optional 21 13110 Lock Nut 22 13124 4mm Hex Wrench ...

Страница 4: ...rial Park High Wycombe Bucks HP14 3BY England declare under our sole responsibility that the product Models UT079 HP079 Gasket Scraper Serial Number to which this declaration relates is in conformity with the following standard s or other normative document s EN792 Draft EN292 Parts 1 2 ISO 8662 1 Pneurop PN8NTC1 following the provisions of 89 392 EEC as amended by 91 368 EEC 93 44 EEC Directives ...

Отзывы: