K. Programming Channel Control
You can program the channel controls (Channel
Up, Channel Down, Last and Numbers) from one Device
to operate in another Device mode. Default channel con-
trol settings on the remote control are as follows:
CBL
: CBL
T V
: CBL
AUD
: AUD
DVD
: DVD
AUX
: AUX
If you wish to store the TV channel controls in TV mode,
use the following steps.
STEP1
Press the [OK/SEL] button and [TV] button simulta-
neously for three seconds. The device LED will turn
on for 30 seconds. The next step must be performed
while the LED is on.
STEP2
Press the [VOL ] button. The device LED will
blink.
STEP3
Press [TV] button. The device LED will blink twice to
confirm the programming.
*Note :
To return TV device to CBL channel repeat steps
above replacing [TV] with [CBL] in Step 3.
L. Programming a ‘Macro’ button.
If your remote model has custom-programmable Macro but-
tons available(See Section 4), they can be programmed to act
as a 'Macro' or Favorite Channel button in CABLE mode. This
allows you to program up to five 2-digit channels, four 3-digit
channels or three 4-digit channels that can be accessed with
one button press.
STEP1
Press the [CBL] button to select the CBL mode.
STEP2
Press the [MACRO] button and [OK/SEL] button
simultaneously for 3 seconds. The [CBL] button
will turn on for 30 seconds.
STEP3
Enter the the 2, 3 or 4-digit code for the
channel you want programmed first (for example,
007) using the Number Pad, then press the
[STOP] button. Then enter the code for the next
channel (for example, 050), then press the [STOP]
button. Repeat this process for the third channel.
The [CBL] button will blink once for each channel
entered.
STEP4
Press the [CH ] button to store the channels
that were selected. The [CBL] button will blink
twice to confirm the storage of commands.
To access the programmed channels, press the [MACRO]
button once. This will bring up the first channel. Press
once again and it will bring up the second channel. Press
again and it will bring up the third channel.
M. RF Setting Method.(RF Frequency: 418Mhz)
STEP1
After installing the MRF-250C, press the [CBL]
and [LIST] button simultaneously for 3 sec-
onds. The [CBL] device LED will turn on indi-
cating that it is ready to be programmed. The
LED will remain on for 30 seconds.
STEP2
Enter the 2-digit ID number assigned to your
MRF-250C ID #. (00~09, A : 10, B : 11, C : 12, D : 13,
E : 14, F : 15)
STEP3
Once you have completed RF ID setting, Store the
2-digit number by pressing the [CBL] button once
again. The [CBL] device LED will blink twice to
confirm that the RF ID number has been stored.
*Note :
Install and select the ID # on the MRF-250C. (For
further details, refer to the MRF-250C manual.) You
can operate up to 15 different equipment locations,
each with an MRF-250C unique Receiver ID #.
N. Low Battery Warning
When the batteries are low and need to be replaced with
fresh batteries, the Device LED lights will blink 2 times in
H. Programming the AUX Device
You can take advantage of the AUX function to program a
devices such as a media PC, gaming console or satellite
radio receiver. Follow the instruction in section B to pro-
gram an AUX device. You can also program the AUX but-
ton for a second TV, DVD or Audio Device. To do this fol-
low the instructions below.
STEP1
Turn on the 5th device you want to program (TV,
AUD, DVD, etc.).
STEP2
Press the [AUX] button and the [OK/SEL] button
simultaneously for 3 seconds. The [AUX] device
LED will turn on for 30 seconds.
STEP3
Press the [Device] button For the type of device you
want to setup. Point the remote control toward the
device and enter the 3-digit code number assigned to
your brand.
*Note :
To program a second TV press TV, etc.
STEP4
When the equipment turns off verify that you
have selected the correct code by pressing the
[POWER] button. The equipment should turn
back on. Then try all of the functions on the
remote control (i.e. volume, mute, etc.) to ensure
you have the correct code. If any of the functions
do not operate as they should, enter the next 3-
digit code number from the brand list.
STEP5
Once you have found the correct 3-digit code, save it
by pressing the [AUX] button one more time. The
[AUX] LED light will blink twice to confirm the code
was stored.
I. Programming the System On/Off Button
This allows you to program the System On/Off button so it
can send up to five power On/Off commands with one but-
ton press.
STEP1
Press the [CBL] button.
STEP2
Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3 seconds.
The [CBL] button will turn on for 30 seconds.
STEP3
Press the first [DEVICE] button you want to store in
the [SYSTEM ON/OFF] button and then the [POWER]
button. Repeat this for other Components until you
have stored all the desired power commands into the
[SYSTEM ON/OFF] button.
STEP4
Press the [CH ] button to save the power com-
mands you stored. The [CBL] button will blink
twice to confirm the commands have been
saved.
J. Programming Volume Control
Volume and Mute control are factory programmed to auto-
matically transfer to the respective Device mode You
select, as follows:
CBL
: CBL
T V
: TV
AUD
: AUD
DVD
: TV
AUX
: AUX
If you wish to store the TV volume control in CBL mode,
use the following steps.
STEP1
Press the [OK/SEL] button and [CBL] button
simultaneously for three seconds. The device
LED will turn on for 30 seconds. The next step
must be performed while the LED is on.
STEP2
Press the [VOL ] button. The device LED will
blink.
STEP3
Press [TV] button. The device LED will blink twice
to confirm the programming.
*Note :
To return CBL device to CBL volume repeat steps
above replacing [TV] with [CBL] in
Step 3 .
Quick Set-up Code Tables
6
Set-up Code Tables
7
0
SANYO
1
SONY
2
SAMSUNG
3
LG
4
TOSHIBA
5
PANASONIC
6
PHILIPS
7
HITACHI
8
SHARP
9
VIZIO
CISCO/SA
001 003 041 042 045 046
PIONEER
001 103 034 051 063 076 105
PACE
001 005 002
SAMSUNG
001 030
MOTOROLA
002 111 148
CE-LABS
164
DIGEO
153
EVOLUTION FTA
158
GENERAL INSTRUMENT 005 103 104
HAMLIN
049 050 055
HITACHI
103 055
JERROLD
005 004 103 005 003 008 009 010 069
MAGNAVOX
010 012
MEMOREX
052
MOXI
111 252 153
NFUSION
192
PANASONIC
044 047
PHILIPS
006 012 013 020 085
PULSAR
052
RCA
047
REGAL
049 050
REGENCY
057
SKY
230 204
SONY
108
SPRUCER
047
TELNET
354
TOCOM
039 040 056
TOSHIBA
052
VIEWSTAR
012 015
ZENITH
052 060 093 100
A MARK
112 143
ABEX
025
ACCURIAN
036
ADMIRAL
072 251 333
ADVENT
247 388
ADVENTURA
002
AIKO
103
AKAI 116 146 248 404 405 473 475 323 387
391 615
ALBATRON
017
ALERON
028
AMERICA ACTION 043
AMPRO 073
AMSTRAD
052
ANAM 043 054 056 080 112
AOC 116 363 112 058 616
APEX
572
APEX DIGITAL
006
AQUAVISION
573 574
ASTAR
477
AUDIOVOX
076 454 388
AVENTURA
052
AVION
441
AXION
039
BELCOR
116
BELL&HOWELL
333 072
BENQ
423 600
BOXLIGHT
266
BRADFORD
043
BROCKWOOD
116
BROKSONIC
238
BYDESIGN
031 032
CANDLE 116 002 003 363
CAPEHART
058
CARY AUDIO DESIGN 266
CELEBRITY
001
CENTURION
116
CETRONIC
043
CHANGHONG
247
CITIZEN 116 002 003 363 043 258 103 143
CLARION
043
CLASSIC 043
CLP CLASSIC
333
COLORTYME
116
CONCERTO
363
CONCIERGE
073
CONTEC 043 050 051
CORNEA
116
CORONADO 143
CRAIG 043 054
CROSLEY
164
CROWN 043 143
CURTIS MATHES 116 258 363 143
CXC 043
CYBERHOME
015
DAEWOO
363 016 043 044 076 103 114 125 127
143
DAYTRON
363 143
DELL
320 164 363 618
DIGITAL PROJECTION 570
DIMENSIA
333
DREAMVISION
235
DUKANE
011 025
DUMONT
116 073
DURABRAND
096 052
DWIN 257
DYNASTY
043
DYNEX
400
EIKI
187
ELECTROBAND
001
ELECTROGRAPH
466
ELECTROHOME 143 024 076 196
ELEKTRA
072
ELEMENT
363 494 526 622
EMERSON
028 048 043 155 005 116 363 047 050
051 076 096 143 153 154 052 514
ENVISION
116
EPSON
324 590
ESA
323
FISHER 007 057
FUJITSU
246 198 410
FUNAI 028 043 052
FUTURETECH 043
GATEWAY
242 268
GE 073 116 008 009 034 056 074 155 333
363
GEM
391
GIBRALTER
116 073
GO VIDEO
026
GOLDSTAR 113 116 102 363 106 112 127 143
GRUNPY
028 043
HAIER
363 501 623
HALL MARK
363
HANNSPREE
349 381
Manufacturer/Brand
Set-Up Code Number
CBL-CABLE Converters
Manufacturer/Brand
Set-Up Code Number
TV
Quick Number
Manufacturer/Brand
TV
0
ROTEL
1
DENON
2
YAMAHA
3
MARANTZ
4
SONY
5
INTEGRA
6
HARMAN KARDON
7
PIONEER
8
ONKYO
9
LEXICON
Quick Number
Manufacturer/Brand
AUDIO
0
HITACHI
1
SONY
2
PHILIPS
3
SAMSUNG
4
PHILIPS MAGNAVOX
5
PANASONIC
6
LG
7
JVC
8
DENON
9
PIONEER
Quick Number
Manufacturer/Brand
DVD
0
BOSE
1
HP
2
APPLE / iPod
3
APPLE / iPod
4
MICROSOFT / XBOX
5
SONY / PS2
6
LUTRON
7
X-10
8
X-10
9
MICROSOFT / XBOX
Quick Number
Manufacturer/Brand
AUX
Manufacturer/Brand
Set-Up Code Number
TV
A. Quick Set-Up Method
STEP1
Turn on the equipment you want to program. To pro-
gram your TV, turn on the TV.
STEP2
Point the remote at the component and press
and hold the [DEVICE] key for 3 seconds until the
Device LED blinks off and turns back on.
Continue holding the [DEVICE] key and press the
number keys, one at a time, starting with 1, then
2, 3...0. Stop pressing the number keys when the
device turns off.
STEP3
Release the [DEVICE] key to save the code. The
Device LED will blink twice to confirm the code is
stored.
Repeat the steps above for all components (TV, AUD,
DVD, AUX).
B. Pre-Programmed 3-Dight Code Method
STEP1
Turn on the equipment that you want the remote
control to operate (Cable Box, TV, DVD, etc.).
STEP2
Press the [DEVICE] button and the [OK/SEL] button
simultaneously for three seconds. The corre-
sponding device LED will turn on indicating that it
is ready to be programmed. The LED will remain
on for 30 seconds. The next step must be entered
while the LED is on.
STEP3
Point the remote control toward the equipment
and enter the three-digit code number assigned
to your brand from the code tables. If there are
more than one three-digit number listed for your
brand, try one code number at a time until your
equipment turns off.
*Note :
You can verify that you have selected the correct
code by pressing the [POWER] button. The equip-
ment should turn back on. Then try all of the func-
tions on the remote control (i.e. volume, mute, etc.)
to ensure you have the correct code. If any of the
functions do not operate as they should, repeat the
instructions from STEP 3 above using the next
three digit code number from the brand list.
STEP4
Store the three-digit code by pressing the same
[DEVICE] button once again. The device LED will
blink twice to confirm that the code has been
stored.
C. Auto-Search Method
If none of the three digit code numbers assigned to your
brand of equipment works, or the code table does not list
your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by fol-
lowing steps:
STEP1
Turn on the equipment that you want the remote
control to operate (Cable Box, TV, DVD, etc.).
STEP2
Press the [DEVICE] button and the
[OK/SEL] button simultaneously for three
seconds. The device LED will turn on indi-
cating that it is ready to be
programmed. The LED will remain on for
30 seconds. The next step must be entered
while the LED is on.
STEP3
Press the [CH ] or [CH ] button one at a time or
keep it pressed. The remote will emit a series of
Power ON/OFF code signals. Release the [CH ] or
[CH ] button as soon as the equipment turns off.
*Note :
You can verify that you have selected the correct
code by pressing the [POWER] button. The equip-
ment should turn back on. Then try all of the func-
tions on the remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any of the func-
tions do not operate as they should, repeat the
instructions from STEP 3 above to continue the Auto
Search Method.
STEP4
Press the same [DEVICE] button to store the code.
The Device LED will blink twice to confirm that the
code has been stored.
D. The Learning Method
STEP1
Press the [DEVICE] button (TV,AUD, DVD, or AUX) to
be programmed and the [ASPECT] buttons simulta-
neously for 3 seconds until the Device LED light turns
on.
STEP2
Line up the
PHAZR-5
to the remote control you
want to "learn" from, head-to-head, 1 or 2 inches
apart.
STEP3
Press the button on the
PHAZR-5
that you want
to teach a command to. For example, press the
[MUTE] button to learn a command to the
[MUTE] button.
STEP4
Press and hold the button on the other remote that
corresponds to the command you want to teach
until the
PHAZR-5
Device LED light blinks twice.
*Note :
The LED will blink 5 times if there was an error
in the learning process. Repeat STEPS 3 and 4
if this occurs. Continue learning other buttons
by repeating STEPS 3 and 4.
STEP5
Once you have completed teaching the
PHAZR-
5
all desired commands for the component, save
the learned commands by pressing the [DEVICE]
and [ASPECT] buttons simultaneously until the
Device LED blinks 3 times. Now test all of the
buttons to make sure they operate correctly.
E. Erasing a Single Learned Command
STEP1
Press the [DEVICE] and [ASPECT] buttons simulta-
neously for 3 seconds until the Device LED light
turns on.
STEP2
Press and hold the button you want to erase for
3 seconds. The Device LED will blink twice to
confirm the erasure.
STEP3
To exit, press and hold both the [DEVICE] and
[ASPECT] buttons simultaneously until the
Device LED blinks 3 times.
F. Erasing All Learned Commands from One Device
STEP1
Press the [DEVICE] and [ASPECT] buttons simulta-
neously for 3 seconds until the Device LED light
turns on.
STEP2
Press and hold both the [DEVICE] button you want
to erase and the [PAUSE] button for 5 seconds.
The Device LED will blink twice to confirm the era-
sure.
STEP3
To exit, press and hold both the [DEVICE] and
[ASPECT] buttons simultaneously
G.To Identify the 3-Digit Code Programmed for a
Device
STEP1
Press the appropriate [DEVICE] button and the
[OK/SEL] button simultaneously for three sec-
onds. The device LED will turn on for 30 seconds.
The next step must be performed while the LED
is on.
STEP2
Press the [INFO] button. The device LED will blink
a number of times indicating the number of each
digit for the code. Each digit is separated by a one
second interval of the LED being off.
Example :
One blink, (pause) three blinks, (pause) eight
blinks indicates the code number 138.
*Note :
Ten blinks indicates the number 0.
sequence whenever a [POWER] button is pressed to turn
on equipment.
O. Memory Lock System
This remote control is designed to retain programmed
memory for 10 years even after batteries are removed
from the remote control.
P. Record Your Component Set-up Codes
TV
Set-up Code Number:
AUD
Set-up Code Number:
DVD
Set-up Code Number:
AUX
Set-up Code Number:
For additional information about your remote control, go to
www.universalremote.com
Q. Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply
with the limits for aClass B digital device, pursuant to
part 15 of the FCC Rules. These limits aredesigned to pro-
vide reasonable protection against harmful interference
in aresidential installation. This equipment generates,
uses and can radiate radiofrequency energy and, if not
installed and used in accordance with the instruc-tions,
may cause harmful interference to radio communica-
tions.
However, there is no guarantee that interference will not
occur in a particularinstallation. If this equipment does
cause harmful interference to radio or tele-vision recep-
tion, which can be determined by turning the equipment
off andon, the user is encouraged to try to correct the
interference by one more of thefollowing measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different fromthat to which the receiver is con-
nected.
Consult the dealer or an experienced radio/TV
technician for help.
Warning!
Changes or modifications not expressly approved by the
manufacturer couldvoid the user's authority to operate
the equipment.
*Note :
The manufacturer is not responsible for any
Radio or TV interferencecaused by unautho-
rized modifications to this equipment. Such
modificationscould void the user's authority to
operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules.
Operation is subject to thefollowing two conditions: (1)
this device may not cause harmful interference,and (2)
this device must accept any interference received,
including interferencethat may cause undesired opera-
tion.
Any changes or modifications not expressly approved by
the party responsiblefor compliance could void the
authority to operate equipment.
The antenna(s) used for this transmitter must not be co-
located or operating inconjunction with any other anten-
na or transmitter.
Button Functions
4
Programming the Remote Control
5
IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, AUD,
DVD or AUX button, depending on what device you are programming the remote to operate.
There are five ways you can program your remote:
* Quick Set-Up Method
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
* The Learning Method
* RF Setting Method
The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit
code. This is the quickest way to set up devices made by popular manufacturers.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit
code numbers that correspond with the components manufacture/brand. Code tables for this method
are on the backside of the operating instructions.
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you
to identify the correct code.
The Learning Method allows you to transfer functions from other remotes to the
PHAZR-5
one button at a time.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
Universal Remote Control, Inc.
www.universalremote.com
OCE-0087C Rev 01 (04/01/11)
Operating Instructions For
PHAZR-5
Cable Remote Control
The PHAZR-5 UR5L-9000LRF & UR5L-
9020LRF is designed to operate the CISCO
/ SA, Pioneer, Pace Micro, Samsung and
Motorola digital set tops, Plus the majority
of TV, AUD, DVD and AUX equipment on
the market as shown below.
CBL
: Cable Set-top Box
TV
: Televisions
AUD
: Audio Receivers
DVD
: DVD Players
AUX
: Media PC, Gaming System, etc.
Introduction
1
DEFAULT STATE:
Device Default:
Cable Set-Top Box (STB)
Channel Default:
CABLE channel and numbers
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers
through the TV or AUD. Refer to section
K
for
programming steps.
Volume Default:
Volume and Mute control are
automatically transferred to the respective
Component based on the Device selected:
CBL
:Cable Set-Top Box ;
TV
:TV ;
AUD
:AUD.
DVD
:TV ;
AUX
:AUX. You have the option of
controlling CABLE Volume and Mute through
the TV, DVD or AUD. Refer to section
J
for
programming steps.
Operations
3
Replacing Batteries
2
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1
Remove the battery compartment cover
on the back of your remote control.
STEP2
Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3
Replace the battery compartment cover.
UR5L-9000LRF & UR5L-9020LRF
