background image

STEP1    

Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR,
or DVD).

STEP2    

Press the [DEVICE] button and the [SELECT/OK] button simultaneously for three seconds.
The corresponding device LED will turn on indicating that it is ready to be programmed.
The LED will remain on for 20 seconds. The next step must be entered while the LED is on.

STEP3    

Point the remote control toward the equipment and enter the three-digit code number
assigned to your brand from the code tables. If there are more than one three-digit
number listed for your brand, try one code number at a time until your equipment turns off.

*Note : 

You can verify that you have selected the correct code by pressing the [MUTE] button. The
equipment should turn on or off.

STEP4    

Store the three-digit code by pressing the same [DEVICE] button once again. The device
LED will blink twice to confirm that the code has been stored.

Universal Remote Control, Inc.

www.universalremote.com

OCE-0009A Rev 05 (08/05/04)

UR3-SR

Operating Manual 

For Easy Clicker  

This remote control is designed to operate
most digital and analog cable boxes, as well
as TVs, and a VCR or DVD player.

A. Manual Programming

The remote control can be programmed by
entering a three-digit code number that
corresponds to particular brands and models
of equipment. The three-digit code numbers
are listed in the code tables sections of this
instruction manual.

Introduction

1

*Note : 

In this section, when you are
instructed to press a [DEVICE]
button, that means you should press
either the CBL, TV, or VCR button,
depending on which device you are
programming the remote to operate.

Installing Batteries

2

Before you program or operate the remote
control, you must install two new AAA alkaline
batteries.

STEP1    

Remove the battery compartment cover
from the back of your remote control.

STEP2    

Check battery polarity carefully, and
install the batteries as shown in the
illustration below.

STEP3    

Replace the battery compartment
cover.

Install two

AAA alkaline batteries

as shown here

Button Functions

3

Programming the Remote Control.

4

*Note : 

Try all the functions on the remote
control. If any of the functions do not
operate as they should, repeat the
instructions from Step 2 using the next
three-digit code number from the same
brand list.

B. Auto Search Method

If none of the three digit code numbers
assigned to your brand of equipment works, or
the code table does not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
equipment by following steps:

STEP1    

Turn on the equipment that you want
the remote control to operate (Cable
Box, TV, VCR, or DVD).

STEP2    

Press the [DEVICE] button and the
[SELECT/OK] button simultaneously
for three seconds. The device LED
will turn on indicating that it is ready
to be programmed. The LED will
remain on for 20 seconds. The next
step must be entered while the LED is
on.

STEP3    

Point the remote control toward the
equipment and alternately press the
[CH+] (or [CH-]) button and the
[MUTE] button. If the right code
number is sent, the equipment will
turn off.

*Note : 

You can verify that you selected the
correct code by pressing the [MUTE]
button again. The equipment should
turn On or Off. 

STEP4    

Press the same [DEVICE] button to
store the code. The Device LED will
blink twice to confirm that the code
has been stored.

C. To find the Three-Digit Code that

Was Programmed using the

Auto Search Method

STEP1    

Press the appropriate [DEVICE]

button and the [SELECT/OK] button

simultaneously for three seconds.

The device LED will turn on for 20

seconds. The next step must be

performed while the LED is on.

STEP2    

Press the [INFO] button. The device

LED will blink a number of times

indicating the number of each digit

for the code. Each digit is separated

by a one second interval of the LED

being off.

Example :

One blink, then three blinks, then

eight blinks indicates the code

number 138.

*Note : 

Ten blinks indicates the number 0.

D. Programming a Second TV to the

VCR Button

STEP1    

Press the [VCR] button and the
[SELECT/OK] button simultaneously
for 3 seconds. The VCR LED will
turn on for 20 seconds. The next
step must be performed while the
LED is on.

STEP2    

Press the [TV] button.

STEP3    

Point the remote control toward the
TV and enter the three-digit code
for your TV from the TV codes
table.

STEP4    

Store the three-digit code by
pressing the [VCR] button. The device
LED will blink twice to confirm that
the code has been stored.

E. Programming for Advanced

Functions.

In the CABLE device mode, the A,B,C and
blank macro buttons can be programmed to
act as macro buttons to send out up to 10
commands with one button press. In this
section, when you’re instructed to press a
[MACRO] button, you need to press either
the A, B, C or blank macro button
(depending on which button you are
attempting to program).

*Note : 

The A, B, and C buttons are not
programmable if you have a digital
cable box made by Pace, Pioneer,
or Scientific-Atlanta cable box.

STEP1    

Press the [CBL] button to select the
CABLE mode.

STEP2    

Press a [MACRO] button and the
[SELECT/OK] button simultaneously
for 3 seconds. The CBL device LED
will turn on for 20 seconds. The
next step must be performed while
the LED is on.

STEP3    

Press up to 10 buttons you wish to
store. The CBL device LED will blink
once for each command entered. 

STEP4    

Press the [CH+] button to store the
functions that are selected. The
CBL device LED will blink twice to
confirm the storage of functions.

To erase the Macro programming and return
to the original function:

STEP1   

Press the [CBL] button to select the
CABLE mode.

STEP2    

Press a [MACRO] button and the

[SELECT/OK] button simultaneously

for 3 seconds. The CBL device LED

will turn on for 20 seconds. The next

step must be performed while the

LED is on.

STEP3    

Press the [CH+] button to erase the

functions stored in the button. The

CBL device LED will blink twice to

confirm that the memory button has

been erased.

F.  Assigning the Volume and Mute

keys to a Different Device 

By default, the volume and mute keys operate

volume and mute functions on the TV. If you

would like those keys to operate those

functions on a different device, follow these

steps.

STEP1     

Press the [SELECT/OK] button and

[CBL] button simultaneously for

three seconds. The device LED will

turn on for 20 seconds. The next step

must be performed while the LED is

on.

STEP2     

Press the [VOL +] button. The device

LED will blink.

STEP3     

Press the [DEVICE] button

corresponding to the device that you

would like the volume and mute

buttons to control. The device LED

will blink twice to confirm the

programming.

Example :

If you wish to have the volume and

mute keys operate your cable box,

press the [CBL] button in Step3.

G.  Assigning the Channel keys to a

Different Device 

By default, the CH UP, CH Down, Numeric

buttons, and LAST keys operate through your

Cable Box. If you would like those keys to

operate those functions on a different device,

follow these steps.

STEP1     

Press the [SELECT/OK] button and

[CBL] button simultaneously for

three seconds. The device LED will

turn on for 20 seconds. The next step

must be performed while the LED is

on. 

STEP2    

Press the [VOL -] button. The device

LED will blink.

STEP3     

Press the [TV] button. The device

LED will blink twice to confirm the

programming.

*Note : 

If you wish to have the channel keys

operate your Cable box, press the

[CBL] button instead of the [TV]

button in Step 3.

Отзывы: