4.
Press CH-. The
Navigator’s red light will blink
twice.
The CABLE key is now unlocked and ready to be
reprogrammed. When you are finished reprogramming the
CABLE key, you can then lock in the code. To reprogram
the CABLE key:
1.
Turn on your Cable Converter.
2.
Press CABLE and release. Press and hold
SETUP until the
Navigator’s red light blinks
twice, then release SETUP.
3.
Enter the first three-digit Cable Converter code
listed in the “SET UP CODES FOR CABLE
CONVERTERS” section. If you perform this
procedure correctly, the red light will blink
twice.
4.
Aim the
Navigator at your Cable Converter and
press POWER. Your Cable Converter should
turn off. If your Cable Converter does not
respond, repeat steps 2-4, trying each code
listed for your brand until you find the one that
operates your Cable Converter. If you still
cannot get your Cable Converter to work with
the
Navigator, try searching for your code as
outlined in the “Searching For Your Code”
section.
5.
Your
Navigator is now programmed to
operate your Cable Converter. Write
your Cable Converter code in the
boxes to the left for future reference.
Remember, if you want to use your
Navigator to operate
your Cable Converter, press the CABLE key first.
NOTE: The CABLE key can be programmed with codes
for DBS Satellites. To program your DBS Satellite, follow
the steps above, entering the three-digit code for your DBS
Satellite instead of the three-digit code for your Cable
Converter.
To lock in the code after you have reprogrammed the
CABLE key:
1.
Press and release CABLE.
2.
Press and hold SETUP until the
Navigator’s red
light blinks twice. Release SETUP.
3.
Press 9 - 9 - 7. The
Navigator’s red light will
blink twice.
4.
Press CH+. The
Navigator’s red light will blink
twice.
Optimus
021
Panasonic
000, 021, 107
Panther
637
Paragon
000
Philips
153, 242
Pioneer
533, 144, 753
Prelude
770
Pulsar
000
RadioShack 315
RCA
021
Regal
020, 259, 273
Runco
000
Samsung
040, 144
Scientific
Atlanta
477, 008, 277
Signal
040
SL Marx
040
Sprucer
021
Starcom
003
Stargate
040, 770
Tandy
258
TeleCaption 221
Teleview
040
Timeless
418
Tocom
012
Toshiba
000
TV86
063
Unika
022, 153
United
Cable
003
Universal
022, 153, 191
Viewstar
063, 258
Zenith
525, 000
SETUP CODES FOR
CABLE CONVERTERS
ABC
003, 008, 014
Allegro
153, 315
Antronix
022
Archer
022, 153, 797
Cabletenna 022
Cableview
022
Century
153
Citizen
153, 315
Comtronics 040
Contec
019
Digi
637
Emerson
797
Everquest
040
Garrard
153
Gemini
242
General
Instrument 476, 003, 276
Goldstar
040, 144
Goodmind
797
Hamlin
009, 020, 259, 273
Jasco
153, 315
Jerrold
476, 276, 003, 012,
014
Memorex
000
Movie Time
063
Novaplex
618
NSC
063
Oak
019
SETUP CODES FOR DBS
SATELLITES
AlphaStar
772
Echostar
775
HTS
775
Hughes
Network
Systems
749
5.
Your
Navigator is now programmed to
operate your Audio Component. Write
your Audio Component code in the
boxes to the left for future reference.
Remember, if you want to use your
Navigator to operate
your Audio Component, press the AUDIO key first.
NOTE: For complete functionality of your Stereo
Components you may need to try both Amplifier codes and
Tuner/Receiver codes.
Jerrold
627
Pace
455
Panasonic
701
Primestar
627
RCA
566
Scientific
Atlanta
355
Sony
639
When you receive your
Navigator, channel changing will
be limited to the CABLE mode through a feature called
Channel Lock. The Channel Lock feature limits channel
changing (e.g. CH +/-, 0 – 9 keys, ENTER and LAST) to
the CABLE mode, even when the
Navigator is in the TV or
VCR mode. To unlock the Channel Lock feature to allow
channel changing in the TV and VCR mode:
1.
Press and hold SETUP until the
Navigator’s
red light blinks twice. Release SETUP.
2.
Press 9 - 9 - 6. The
Navigator’s red light will
blink twice.
3.
Press CH-. The
Navigator’s red light will blink
twice.
Now, each individual mode (TV, VCR and CABLE) will
control channel changing.
NOTE: The Channel Lock feature, whether it is locked or
unlocked, will not effect the AUDIO mode.
To reactivate the Channel Lock feature to limit channel
changing to the CABLE mode:
1.
Press and hold SETUP until the
Navigator’s
red light blinks twice. Release SETUP.
2.
Press 9 - 9 - 6. The
Navigator’s red light will
blink twice.
3.
Press CH+. The
Navigator’s red light will blink
twice.
To program the
Navigator to operate your Audio
Component (CD Player, Receiver, Amp or Digital Audio
Service):
Look at the brand name of your Audio Component and
then write it in the space below.
Audio Brand:
Locate the brand name of your Audio Component in the
“SETUP CODES FOR AUDIO COMPONENTS” section.
The brands are listed in alphabetical order with the most
popular codes listed first. You will use one of these codes
to program your
Navigator to operate your Audio Component.
To program the
Navigator to operate your Audio Component:
1.
Turn on your Audio Component. If you are
setting up a CD Player, turn on your CD Player
and insert a compact disc.
2.
Press AUDIO and release. Press and hold
SETUP until the
Navigator’s red light blinks
twice, then release SETUP.
3.
Enter the first three-digit Audio Component
code listed in the “SET UP CODES FOR
AUDIO COMPONENTS” section. If you
perform this procedure correctly, the red light
will blink twice.
4.
Aim the
Navigator at your Audio Component
and press POWER. If you are setting up a CD
Player, aim the
Navigator at your CD Player
and press PLAY. Your Audio Component
should turn off or your CD Player should play
your disc. If your Audio Component does not
respond, repeat steps 2-4, trying each code
listed for your brand until you find the one that
operates your Audio Component. If you still
cannot get your Audio Component to work with
the
Navigator, try searching for your code as
outlined in the “Searching For Your Code”
section.
Searching For Your Code
If your TV, VCR, Cable Converter or Audio Component
does not respond to the
Navigator after trying all of the
codes listed for your brand, or if your brand is not listed at
all, try searching for your code. For example, after trying
all of the codes for your TV, you still cannot get the
Navigator to operate your TV, then:
1.
Turn on your TV.
2.
Press TV and release. Press and hold SETUP
until the
Navigator’s red light blinks twice, then
release SETUP.
3.
Press 9 - 9 - 1.
4.
Slowly alternate between pressing POWER*
and TV until your TV turns OFF. Make sure
that the
Navigator is aimed at your TV during
the search. You may have to press this
sequence of buttons (POWER* then TV) up to
100 times to search the entire library of codes.
5.
When your TV turns OFF, press and release
SETUP to lock in the code for your TV. Your
Navigator is now programmed to operate your
TV.
NOTES: To search for the codes of your other
components, repeat Steps 1 through 4, only substitute the
appropriate device key (VCR, CABLE or AUDIO) for the
component you are searching for.
*If you are searching for your VCR or CD Player code, you
may want to use the PLAY key instead of the POWER key
to search for your code. When your VCR or CD Player
starts to play, press SETUP to lock in your code.
Learning The Codes Programmed
Into The
Navigator
If you have set up the
Navigator using the “Searching For
Your Code” procedure, you may need to find out which
three-digit code is operating your equipment. Use this
procedure
after you have set up your components to find
out which three-digit code is operating your equipment.
For example, to find out which code is operating your TV:
1.
Press TV and release. Press and hold SETUP
until the
Navigator’s red light blinks twice, then
release SETUP.
2.
Press 9 - 9 - 0.
3.
For the first digit of your three-digit code, press 1,
wait 3 seconds and count the number of times the
red light (LED) blinks on the
Navigator. If the light
does not blink when you press the number 1, the
digit is zero.
4.
For the second digit, press 2, wait 3 seconds
and count the number of times the red light
(LED) blinks on the
Navigator. If the light does
not blink when you press the number 2, the
digit is zero.
5.
For the third and final digit, press 3, wait 3
seconds and count the number of times the
red light (LED) blinks on the
Navigator. If the
light does not blink when you press the number
3, the digit is zero. Now you have your
three-digit code.
NOTE: To find the code for your other components, repeat
Steps 1 through 5, only substitute the appropriate device
key (VCR, CABLE or AUDIO) for the component you wish
to get the code for.
Re-Assigning Device Keys
You can use the
Navigator to operate a second TV or a
second VCR or any combination of four home entertainment
components. For example, you may want your
Navigator to
control 1 TV, 1 Cable Converter and 2 VCRs. To accomplish
this, you must re-assign one of the keys to operate the
desired component, in this case, a second VCR. Please note
that the CABLE key cannot be re-assigned. The chart below
shows you how to re-assign a particular device key and then
set up your new component.
TV to VCR
SETUP* + 992 + VCR + TV + TV +
SETUP* + VCR code.
TV to AUDIO
SETUP* + 992 + AUDIO + TV + TV +
SETUP* + Audio Component code.
VCR to TV
SETUP* + 992 + TV + VCR + VCR +
SETUP* + TV code.
VCR to AUDIO SETUP* + 992 + AUDIO + VCR + VCR +
SETUP* + Audio Component code.
AUDIO to TV
SETUP* + 992 + TV + AUDIO + AUDIO
+ SETUP* + TV code.
AUDIO to VCR SETUP* + 992 + VCR + AUDIO +
AUDIO + SETUP* + VCR code.
*
NOTE: Here you must hold SETUP until the Navigator’s
red light blinks twice.
Volume Lock
When you receive your
Navigator, volume control is
operated through your Television using a feature called
Volume Lock. If your TV is not remote controllable, or if
you would like the volume to be controlled by a different
component, you can change the Volume Lock setting to
control the volume through the
CABLE, VCR or AUDIO
mode. Changing the Volume Lock setting to the CABLE or
VCR mode will change the volume control for all modes
except AUDIO, which will continue to control its own
volume. If you change the Volume Lock setting to the
AUDIO mode, all modes (TV, VCR, CABLE and AUDIO)
will be controlled by the AUDIO mode. To change the
Volume Lock setting on the
Navigator to the CABLE or
AUDIO mode:
1.
Press and hold SETUP until the
Navigator’s red
light blinks twice, then release SETUP.
2.
Press 9 - 9 - 3. The
Navigator’s red light will
blink twice.
3.
Press and release CABLE or AUDIO. The
Navigator’s red light will blink twice.
Now, whenever you press VOL+ , VOL- or MUTE on the
Navigator, your cable converter or audio component will
control the volume.
If you have a TV/VCR combination that does not use a TV
code to control the volume, you can access the volume in
the VCR mode. To change the Volume Lock setting on the
Navigator to the VCR mode:
1.
Press and hold SETUP until the
Navigator’s red
light blinks twice, then release SETUP.
2.
Press 9 - 9 - 3. The
Navigator’s red light will
blink twice.
3.
Press and release VCR. The
Navigator’s red
light will blink twice.
Now, whenever you press VOL+ , VOL- or MUTE on the
Navigator, your TV/VCR combo will control the volume.
To return the Volume Lock setting to the TV mode:
1.
Press and hold SETUP until the
Navigator’s red
light blinks twice, then release SETUP.
2.
Press 9 - 9 - 3. The
Navigator’s red light will
blink twice.
3.
Press and release TV. The
Navigator’s red
light will blink twice.
Now, whenever you press VOL+ , VOL- or MUTE on the
Navigator, your TV will control the volume.
Troubleshooting
Problem
Solution
Red light does not
blink or blinks 5 times
when you press a
key?
The red light blinks
when you press a key
but you receive no
response from your
home entertainment
component?
The
Navigator does
not operate your home
entertainment
components or is not
performing commands
properly?
Problems
programming a
TV/VCR combo?
VCR not recording?
No volume on a 2nd
TV ?
C/- and
LAST not working for
your RCA TV?
Problems changing
channels?
Replace the batteries with four
(4) new AAA alkaline batteries.
Make sure you are aiming your
Navigator at your home
entertainment component and
that you are within 15 feet of the
component you are trying to
operate before using your
remote.
Try all of the codes listed for your
brand of home entertainment
component in the “Set-Up
Codes” section. Many setup
codes may allow for partial
functionality, however, only one
setup code will operate your
home entertainment component
correctly. Make sure that all of
the components you are
setting up are able to be
operated with an infrared
remote control.
Use the VCR setup codes for
your brand. Some combo units
may require both a TV code to
control volume and a VCR code
for full operation.
As a safety feature on the
Navigator, you must press the
REC key twice.
Press and hold SETUP until the
Navigator’s red light blinks twice.
Release SETUP and enter 9-9-3
followed by VOL +.
Due to RCA design (1983-1987),
only the original remote control
will operate these functions.
If your original remote control
required an ENTER keystroke
when changing channels, press
the ENTER key on the
Navigator
after you enter the channel
number.
World Wide Web: http://www.oneforall.com
The UNIWAND “
Navigator” does not have any user
serviceable parts. Opening the case, except the battery
cover, may cause permanent damage to your UNIWAND
“
Navigator”.
Uniwand is a trademark of Universal Electronics Inc.
Copyright 1998 by Universal Electronics Inc. No part of
this publication may be reproduced, transmitted,
transcribed, stored in any retrieval system, or translated to
any language, in any form or by any means, electronic,
mechanical, magnetic, optical, manual, or otherwise,
without the prior written permission of Universal
Electronics Inc.
URC-44XXX BO2/BO4
McK
M4078
2/98
CH
-
CABLE
SETUP
POWER
SETUP
CABLE
9 - 9 - 7
9 - 9 - 7
CH
+
9 - 9 - 1
9 - 9 - 1
POWER
PLAY
AUDIO
SETUP
9 - 9 - 6
9 - 9 - 6
SETUP
9 - 9 - 6
9 - 9 - 6
SETUP
CH
-
CH
+
SETUP CODES FOR
AUDIO COMPONENTS
Setup Codes For CD
Players
Aiwa
124, 157
Burmester
420
California
Audio Lab 029
Carver
157, 179, 437
Denon
003
DKK
000
Emerson
305
Fisher
048, 174, 179
Garrard
393, 420
Genexxa
032, 305
Hitachi
032
JVC
072
Kenwood
028, 037, 048, 190
Krell
157
Linn
157
LXI
305
Magnavox
157, 305
Marantz
029, 157, 180
MCS
029
Mission
157
MTC
420
Nikko
174
NSM
157
Onkyo
101
Optimus
000, 032, 037, 048,
145, 179, 305, 420,
437, 468
Panasonic
029
Philips
157
Pioneer
032, 244, 305, 468
Proton
157
QED
157
Quasar
029
RCA
179, 305
Realistic
179, 180, 420
Rotel
157, 420
SAE
157
Sansui
157, 305
Sanyo
179
Scott
305
Sears
305
Sharp
037, 180
Sherwood
180
Sony
000, 185
Soundesign 145
Tascam
420
TEAC
174, 180, 393, 420
Technics
029
Victor
072
Wards
157
Yamaha
036
Yorx
461
Setup Codes For
Receivers
ADC
531
Aiwa
121, 158, 189
Capetronic 531
Carver
042, 189
Casio
195
Clarinette
195
Denon
004
Fisher
042, 219
Garrard
463
Harman/
Kardon
110
JVC
074
Kenwood
027, 186
Linn
189
Lloyd’s
195
LXI
181
Magnavox
189, 195, 531
Marantz
039, 189
MCS
039
Modulaire
195
NAD
320
Onkyo
135
Optimus
042, 181, 186, 219,
531, 670
Panasonic
039
Penney
195
Philips
189
Pioneer
150, 531, 630
Quasar
039
RCA
054, 530, 531
Realistic
181, 195
Sansui
189
Sanyo
219
Sharp
186
Sherwood
502
Sony
158, 474
Soundesign 670
TEAC
463
Technics
039, 309, 518
Victor
074
Wards
042, 054, 158, 189
Yamaha
176, 186
Yorx
195
Setup Codes For
Amplifiers
Denon
160
GE
078
JVC
331
Luxman
165
Optimus
013, 300, 395
Pioneer
013, 300
Realistic
395
Sony
220, 689
Soundesign 078, 211
Technics
308
Victor
331
Wards
013, 078, 211
Yamaha
133, 354
Setup Codes For
Digital Audio Service
Jerrold
459, 520
Scientific
Atlanta
460
Starcom
459
TV
SETUP
TV
SETUP
9 - 9 - 0
9 - 9 - 0
1
1
2
2
3
3
AUDIO
SETUP
9 - 9 - 3
9 - 9 - 3
CABLE
SETUP
9 - 9 - 3
9 - 9 - 3
VCR
SETUP
9 - 9 - 3
9 - 9 - 3
TV
POWER
TV
SETUP
