Universal Audio Ampex ATR-102 Скачать руководство пользователя страница 198 | Manualshive

Страница: 198 / 428

background image

UAD Powered Plug-Ins Manual

- 198 -

Chapter 20: Manley Massive Passive EQ

• You may also find yourself getting away with what seems like massive

amounts of boost. Where the knobs end up, may seem scary particularly for
mastering. Keep in mind that, even at maximum boost, a wide bell might
only max out at 6 dB of boost (less for the lowest band) and only reaches
20 dB at the narrowest bandwidth. On the other hand, because of how
transparent this EQ is, you might actually be EQing more than you could
with a different unit. Taste rules, test benches don't make hit records, believe
your ears.

• Sometimes the shelves will sound pretty weird, especially (only) at the nar-

row bandwidth settings. They might seem to be having a complex effect and
not only at the “dialed in” frequency. This is certainly possible. Try wider
bandwidths at first.

• If you seem to be boosting all 4 bands at widely separated frequencies and

not hearing much “EQ” as you might expect (except for level) this is a
side-effect of a passive EQ and probably a good thing. To get drastic sound-
ing EQ you should try boosting a few bands and cutting a few bands. In
fact, it is usually best to start with cutting rather than boosting.

• A reasonable starting point for the Bandwidth for shelves is straight up or

between 11:00 and 1:00. It was designed this way and is roughly where
the maximum flatness around the “knee” is, combined with a well defined
steep slope.

• The Massive Passive may sound remarkably different from other high end

EQs and completely different from the console EQs. Yes, this is quite delib-
erate. Hopefully it sounds better, sweeter, more musical and it complements
your console EQs. We saw little need for yet another variation of the stan-
dard parametric with only subtle sonic differences. We suggest using the
Massive Passive before tape, for the bulk of the EQ tasks and then using the
console EQs for some fine tweaking and where narrow Q touch-ups like
notches are needed. The Massive Passive is equally at home doing big,
powerful EQ tasks such as is sometimes required for tracking drums, bass
and guitars, or for doing those demanding jobs where subtlety is required
like vocals and mastering.

«
...
196
197
198
199
200
...
»

Содержание Ampex ATR-102













































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ampex ATR-102

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: Federal Signal Corporation Страницы: 12

Бренд: ParaBody Страницы: 5

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Sabre Страницы: 2

Бренд: Nabtesco Страницы: 26

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: Öhlins Страницы: 8

Бренд: ?HC Страницы: 2

i-limb access hand

Бренд: Össur Страницы: 246

PROPRIO FOOT PSX01

Бренд: Össur Страницы: 374

STOMAMED COL-160

Бренд: Orliman Страницы: 12

Бренд: CAB Страницы: 30

NTP TECHNOLOGY DAD Thunder Core 256

Бренд: DAN Страницы: 16

Бренд: American DJ Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды