Unity CV2.1 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 12

Unity CV2.1 Скачать руководство пользователя страница 8

Commissioning

8

Resetting your Unity CV2.1 must be carried out by a qualified electrician or
competent person.

Whist the fan is running, remove both the outer cover and main body cover of the
fan (see installation section page 4).

Locate the ‘reset’ button and depress using a small ‘pin-sized’ tool for 3 seconds.
All lights will turn on to show the unit has been reset.

Turn the power OFF to the fan

refit the main body cover.

Locate main body cover via the arrow & unlock position, rotate clockwise to
'lock position'.

Tighten retaining screw until main body cover cannot be opened.

Turn the power to the fan ON

recommission (see page 7).

Note:

Your fan will remember its previous timer and humidity settings, if required,

these can be changed during the recommissioning section.

To master reset and recommission your Unity CV2.1

Airflow Settings

l/s

Trickle

Boost

Bathroom

(Default)

6

8

Kitchen

(Default)

8

13

Performance Graph - airflow characteristics

«
...
6
7
8
9
10
...
»

Содержание CV2.1













Отзывы:

Нет отзывов