Unitronics Vision V350-35-TU24 Скачать руководство пользователя страница 8

 

Vision™PLC+HMI Installation Guide  

 

 

Unitronics 

 

Transistor Outputs (pnp) 

 

  The 0V signals of the transistor and the analog outputs 

must be connected to the controller’s 0V. 

  Outputs 1 to 6 can be used as PWM outputs. 

   

   

   

Power Supply 

The controller requires an external 24VDC power supply. 

 

  The power supply must include double insulation. Outputs must be rated as  

SELV/PELV/Class2/Limited Power. 

 

  Use separate wires to connect the functional 

earth line (pin 3) and the 0V line (pin 2) to the 
system earth ground. 

  Install an external circuit breaker. Guard 

against short-circuiting in external wiring. 

  Double-check all wiring before turning  

on the power supply. 

 

Do not connect either the ‘Neutral’ or ‘Line’  

signal of the 110/220VAC to device’s 0V pin 

  In the event of voltage fluctuations or non-

conformity to voltage power supply 
specifications, connect the device to  
a regulated power supply. 

 

     

Earthing the PLC+HMI  

To maximize system performance, avoid electromagnetic interference by: 

  Mounting the controller on a metal panel. 

  Connect each common and ground connection directly to the earth ground of your system. 

  For ground wiring uses the shortest and thickest possible wire. 

   

Communication  

  

V350-35-TU24/V350-J-TU24

 models comprise built-in ports: 1 USB and 1 RS232/RS485 (Port 1). 

 
Note that physically connecting a PC to the controller via USB suspends RS232/RS485 
communications via Port 1. When the PC is disconnected, RS232/RS485 resumes. 

 

Содержание Vision V350-35-TU24











Отзывы: