Unitronics Vision OPLC V130-33-TR34 Скачать руководство пользователя страница 10

Страница: 10 / 10

V130-33-TR34 Installation Guide

Changing I/O Settings

1. The I/O board of the controller is now exposed, enabling you to change I/O settings according to

the jumpers shown on page 5.

Changing Communication Settings

1. To access the communication jumpers,

hold the I/O PCB board by its top and
bottom connectors and steadily pull the
board off.

2. Locate the jumpers, and then change

the settings as required. Jumper
settings are shown on page 9.

Closing the Controller

1. Gently replace the board. Make

certain that the pins fit correctly into
their matching receptacle.
Do not force the board into place;
doing so may damage the controller.

2. Replace the back cover of the

controller and fasten the corner
screws.

Note that you must replace the back cover securely before powering up the controller.

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 287 19 19

[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

[email protected]

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected]

Содержание Vision OPLC V130-33-TR34











Результаты поиска

Содержание Vision OPLC V130-33-TR34

Отзывы:

Бренды по названию

Популярные бренды

Unitronics Vision OPLC V130-33-TR34, Руководство по установке

Результаты поиска

Содержание Vision OPLC V130-33-TR34

Отзывы:

Бренды по названию

Популярные бренды