Unitronics Vision OPLC V130-33-B1 Скачать руководство пользователя страница 1

Страница: 1 / 8

Unitronics

Vision™ OPLC™

Installation Guide

V130-33-B1/V130-J-B1

V350-35-B1/V350-J-B1

V430-J-B1

General Description

All of the controllers covered in this guide are micro-OPLCs, rugged programmable logic controllers that

comprise built-in operating panels.

Item

V130-B1

V130J-B1

V350-B1

V350J-B1

V430J-B1

Screen

2.4"

3.5" Color Touch

4.3" Color Touch

Keypad

Yes

None

Function Keys

None

Yes

Com Port, Built-in

RS232/485

Yes

Yes*

USB device,

mini-B

None

Yes*

Com Ports, separate

order, user-installed

The user may install a CANbus port (V100-17-CAN), and

one

of the following:

•

RS232/RS485 port (V100-17-RS4/V100-17-RS4X)

•

Ethernet (V100-17-ET2)

•

Profibus Slave (V100-17-PB1)

* V430J comprises both RS232/485 and USB ports; note that only

one

channel may be used at a time.

Standard Kit Contents

Item

V130-B1

V130J-B1

V350-B1

V350J-B1

V430J-B1

Controller

Yes

Terminal Blocks

Yes

Battery (installed)

Yes

Slides

(2 sets of key labels)

None

Yes

None

Mounting Brackets

Yes (2 parts)

Yes (4 parts)

Rubber Seal

Yes

Programming cable

+ RS232 adapter

Yes

None

USB

programming cable

None

Yes

Содержание Vision OPLC V130-33-B1









Результаты поиска

Содержание Vision OPLC V130-33-B1

Отзывы:

Похожие инструкции для Vision OPLC V130-33-B1

Бренды по названию

Популярные бренды

Unitronics Vision OPLC V130-33-B1, Инструкция по установке

Результаты поиска

Содержание Vision OPLC V130-33-B1

Отзывы:

Похожие инструкции для Vision OPLC V130-33-B1

Бренды по названию

Популярные бренды