Unitech MS340BT Скачать руководство пользователя страница 35

Страница: 35 / 75

© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd

2. Numeric Bar

Codes (Appendix A)

3.4 Code 128 Parameters

A. Reading Type

B. Check Digit

Transmission

C. Append FNC2

UCC/EAN-128 Disable * UCC/EAN-128 Enable

Calculate Check

Digit& Not Transmit *

OFF*

Enable ‘]C1‘Code

Format *

Disable ‘]C1‘Code

Format

Calculate Check Digit

& Transmit

Enable Code128

Group Separators(GS) *

Disable Code128

Group Separators(GS)

Do Not Calculate

Check Digit

D. Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.

Variable *

Fix Length (2 Sets Available)

1. 1

Set Begin 3. 1

Set Complete

1. 2

Set Begin 3. 2

Set Complete

Minimum Length

1. Begin 3. Complete

2. Numeric Bar

Codes (Appendix A)

2. Numeric Bar

Codes (Appendix A)

Содержание MS340BT



































































Результаты поиска

Содержание MS340BT

Отзывы:

Похожие инструкции для MS340BT

Бренды по названию

Популярные бренды

Unitech MS340BT, Руководство пользователя

Результаты поиска

Содержание MS340BT

Отзывы:

Похожие инструкции для MS340BT

Бренды по названию

Популярные бренды