manualshive.com logo in svg

Unison ERn2-RM-120, Руководство по установке

Поделиться
Скачать
Unison ERn2-RM-120 Скачать руководство пользователя страница 18

14

Unison

®

 ERn Rack Mount Enclosure Installation Manual

1: Pull Belden 8471 (or approved equal type) control wiring to the rear panel of the ERn enclosure.

2: Strip 3/16” (5mm) of insulation from the ends of each wire pair.

3: Remove the LinkConnect connector (labeled LON).

• Notice the LinkConnect connector is labeled to indicate that 

the connector is split between two segments, allowing three 
station wire home runs per segment. This is effective only 
when a Paradigm dual station repeater module (P-DREP) is 
used. With the standard Paradigm station repeater module (P-
REP) you may connect up to six station home runs to the 
connector for the single control segment.

4: Loosen the terminal screws for as many wire pairs you are 

terminating. Keep in mind that the connector is split into two 
segments. Be sure to terminate each wire pair to the correct 
segment.

5: Insert each white (typical) wire from the pairs into an “A” 

terminal on the connector and tighten the screw firmly to secure the wire into the connector.

6: Insert each black (typical) wire from the pairs into an “B” terminal on the connector and tighten 

the screw firmly to secure the wire into the connector.

7: The 14 AWG (2.5mm

2

) ground wire can terminate to the ground bus located on the rear panel 

of the ERn enclosure. Connect the other end of the ground wire to the green/yellow striped wire 
connected at the architectural control station using a WAGO connector. Reference the related 
station installation manual for further details.

8: Replace the connector to the rear panel I/O.

Note:

When utilizing a Paradigm station repeater module (P-REP) or Paradigm dual station 

repeater module (P-DREP), terminate the repeated segment(s) and auxiliary power 

wiring to the related rear panel I/O board.

1A

1B

1A

1B

1A

1B

2A

2B

2A

2B

2A

2B

Содержание ERn2-RM-120

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды