5
4
Step5.BikeInstallation
5-1Firstly,confirmthatthespecificationsoftherearwheelhubof
thebikematchthehubconfigurationofthebiketrainer.
5-2 Adjust the gear of the bike to disassemble the rear wheel.
Suggestedchainposition:thefrontderailleurisonthechainwheel,the
rearderailleurisonthesmallestfreewheeltoothplate.Loosentherear
wheelquickreleaseandremovetherearwheel.
Tip: If there is no quick release for the bike trainer, the quick
releaseontherearwheelcanbedisassembledandutilized.
5-3 Install the bike on the bike trainer: the chain at the rear
derailleurofthebikehangsonthesmallesttoothplateofthefreewheel
ofthebike,thebackforkofthebikeisplacedlightlyontheleftandright
axles of the bike trainer that supports the quick release. After
confirmingalignment,pressdownthebike.Thebackforkofthebikeis
supportedontheleftandrightaxlesofthebiketrainer.Toensurethat
thebackforkofthebikeisfullysupportedonthebiketrainer,thefront
wheelofthebikecanbeliftedoffthegroundandswinggently,andthen
putitdown.
5-4FixtheQuickRelease:Onehandrotatesthenutattheendof
the quick release, the other hand presses the locking wrench of the
quickrelease.Asthepressureisappropriate,pressthelockingwrench
ofthequickreleasetothefullylockedposition.(Ifthelockingwrenchof
thequickreleasecannotbepresseddown,pleasefirstunscrewthenut
attheendofthequickrelease,theninstallandfixitaccordingtothe
abovemethod.)
Step3.BikeTrainerLeveling
Afterinstallingthebasepipe,asshowninFigure3,thebiketrainer
isplacedonsolidflatground.Itisleveledbyrotatingthebasesleeveon
thebasepipesothatthefourbasesleevestouchthegroundcompletely
atthesametime,andthebiketrainerwouldnotshake.
Attention: Before use, the bike trainer must be leveled to avoid
accidentalinjurycausedbyshakingofthebiketrainer.
Attention:Thenutsconnectingthebasepipe1withthemainbeam
andthebasepipe2withthemovablesupportmustbefastenedfirmly!
Step4.HubPartsAssembly
4-1FreeWheelInstallation
The bike trainer is compatible with SHIMANO/SRAM card type
flywheelwiththespeedof8/9/10/11.AshowninFigure4,ifyouusethe
8/9/10-speed flywheel, a shim must be put on the hub before the
flywheel is fitted. If you use an 11-speed flywheel, the flywheel can
directly fit without installing the adjusting shim. After the flywheel is
fitted,asshowninFigure5,screwtheflywheelnut,andfastenthenut
withaspecialwrenchforflywheelassembly.
fixingjointofthequickrelease,theninsertitintothemainbeamaxle
hole.Ifusing130bikeframe,theleftfixingjointofthequickreleasecan
bedirectlyinsertedintothemainbeamaxleholewithoutinstallingthe
bikeframeconversionsleeve.
4-3QuickReleaseInstallation
Thebiketrainerissuitablefor5mmquickrelease.Youcanusethe
quickreleaseofthebackwheelofyourbikeorequipitseparately(this
productisnotequippedwiththisaccessory).
1）Firstremovethenutandone-sidespringattheendofthequick
release,andtheotherspringisleftonthequickrelease.
2）InthedirectionshowninFig.6,thequickreleaseispenetrated
theleftaxlehole,andtheotherendispenetratedthroughtherightaxle
(fixedonthebiketrainer).
3）As shown in Figure 6, reinstall the spring and nut removed
beforetokeepthequickreleaseloosetoinstallthebike.
4-2InstallationofFixingJointofQuickRelease
Thebiketraineriscompatiblewithbikeframeconversionofwith
thebackforkwidthof130/135,asshowninFigure6.Ifusinga135bike
frame, the bike frame conversion sleeve shall be firstly put in the left
Attention: While installing the quick release, the conical spring
headofthequickreleasemustbeinward(facingthebikebody)!
