Add LPCU-As to the LPLUS
At this time you can add LPCU-As.
1. Press the
Activate Discovery Mode
button.
2. Press the button on the front of the LPCU-A when
prompted.
3. After a few seconds, the LPLUS should detect
the LPCU-A. Give the detected LPCU-A a description
and assign it to the desired scene.
4. Press the
Submit
button when done.
5. Repeat steps 1-4 for each LPCU-A to add.
To add an LPRO, click
Activate Discovery Mode
then
Hardware on the Location page.
Edit LPCU-A Equipment
Click the blue pencil icon to edit LPCU-A description or
change scene assignment.
Delete LPCU-A Equipment
Click the blue trashcan icon to delete a LPCU-A.
Update the Firmware
LPCU-A, a
Manage Firmware
command will be displayed
under ‘Hardware’ on the Location screen. Click the link to
update hardware. Select the Device(s) and click
Update
Firmware
to start.
Support
Model Name: SMRT Logic
Model Number: LPLUS
Dimensions: 4.4” x 3.1” x 1.2” without antenna
Unit Weight: 3.4oz (95g) without accessories
Power: 5Vdc, 1A
Port Speed: 10/100 Mbps
Operating Temp: 32 to 104°F (0-40°C)
Storage Temp: -4 to 140°F(-20 to 60°C)
Operating Humidity: 10 to 80% RH, non-condensing
FCC Statement - FCC ID: OF7SCG
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
In order to maintain compliance with the FCC RF exposure guidelines, this
device should be installed and operated with a minimum distance of 20cm
between the radiator, and the body of the operator and/or nearby persons.
compliance could void the user’s authority to operate this device.
Permitted Low Gain Dipole Whip Antenna (2dBi).
IC Statement - IC: 3575A-SCG
1. Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d’un type et d’un gain
maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l’intention
des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte
que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l’intensité nécessaire à l’établissement d’une communication satisfaisante.
2. This radio transmitter has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible
gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with
this device.
catégorie I) a été approuvé par Industrie Canada pour fonctionner avec
les types d’antenne énumérés ci-dessous et ayant un gain admissible
maximal et l’impédance requise pour chaque type d’antenne. Les types
d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain
maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Antenna Approved/Antenne approuvé
Type/Type
Max. Gain/Max. Gain
Impedance/Impédance
Dipole Whip
2.0 dBi
50 Ω
3. This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
4. In order to maintain compliance with the IC RF exposure guidelines, this
device should be installed and operated with a minimum distance of 20 cm
between the radiator, and the body of the operator and/or nearby persons.
IC, ce
dispositif doit être installé et exploité avec une distance minimale de 20 cm
entre le radiateur et le corps de l’opérateur ou à proximité de personnes.
FCC and IC Statements
Visit www.uniquelighting.com for FAQ and detailed instructions.
To submit a help ticket, click on the Contact link then the
Submit a Ticket
link.
