Unipulse UPM100 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 89

background image

37

6

　

Explanation of the Alarm Detection Function

37

Chapter

6

Alarm can be output as a contact signal that can be utilized for emergency stoppage of system and
so on, when voltage, current or electric power exceeds the set value.
Measurements in between seven seconds before and three seconds after the alarm is detected are
recorded in the main unit 10 times per second.
This can be used for examining the cause and mechanism of faults occurred.
A single item from voltage, current or electric power is settable for each of the two settings.
The order of priority is voltage > current > electric power.
For example, when UV interphase voltage and effective power are set, only the UV interphase
voltage is enabled and the effective power is canceled.
Same types may be selected multiply.
As for same types, the alarm is detected whenever any one of the selected items exceeds the alarm
detection level.

6-1.

Alarm detection item setting 1

Configure alarm detection item setting 1.

<<Setting value>>

0 0 0 0 0 0

6

Explanation of the Alarm
Detection Function

6HYHQVHFRQGVEHIRUH

7KUHHVHFRQGVDIWHU

7KUHVKROGYDOXHVDUHVHWIRU
YROWDJHRIDODUPGHWHFWLRQ
IXQFWLRQFXUUHQWDQGVRRQ
DQGDQDODUPLVGHWHFWHGLI
WKHVHWYDOXHVDUHH[FHHGHG

$ODUPUHFRUGHUIXQFWLRQ
VHFRQGV[ SRLQW
LVDXWRPDWLFDOO\UHFRUGHGD
VLQJOHZDYHIRUPLVUHFRUGHG

Invalid

0 fixed.

0 to 7

Turns UV interphase voltage (B0) VW interphase voltage (B1) WU interphase voltage (B2)

0/1

Turns average phase current (B0) ON and OFF.

0/1

Turns average interphase voltage (B0) ON and OFF.

0 to 7

Turns effective power (B0) / reactive power (B1) / apparent power (B2) ON and OFF.

0 to 7

Turns U phase current (B0) V phase current (B1) W phase current (B2) ON and OFF by BIT.

ON and OFF by BIT.

«
...
44
45
46
47
48
...
»

Содержание UPM100


























































































Отзывы:

Нет отзывов

Похожие инструкции для UPM100

Бренд: C-LOGIC Страницы: 2

Бренд: Campbell Страницы: 362

Бренд: Campbell Страницы: 60

Бренд: Campbell Страницы: 116

Бренд: Campbell Страницы: 30

Бренд: Campbell Страницы: 55

Бренд: Keithley Страницы: 201

Бренд: PAT Страницы: 57

Clavinova CVP-601

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 28

Бренд: Magnescale Страницы: 64

SourceMeter 2430

Бренд: Keithley Страницы: 141

CoolPoint CP12-V8

Бренд: UFM Страницы: 14

Nitro-Save NS16

Бренд: TDI Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: Zero 88 Страницы: 32

Бренд: Hanna Instruments Страницы: 2

American AL-1000

Бренд: Badger Meter Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды