Unipulse UPM100 Скачать руководство пользователя страница 42

Страница: 42 / 89

Function Description Related to Indicated Values

Chapter

Sub display section

Press the

key to change the content displayed.

1) (

∑

)

Right side:

Average interphase voltage [V]

Left side:

Average phase current [A]

→

2) (1)

Right side:

UTM1 torque [Nm]

Left side:

UTM1 rotation speed [rpm]

→

3) (2)

Right side:

UTM2 torque [Nm]

Left side:

UTM2 rotation speed [rpm]

→

4) (AUX)

Right side:

AUX1 external voltage input [V]

Left side:

AUX2 external voltage input [V]

→

5) (AUX)

Right side:

TEMP1 temperature [°C]

Left side:

TEMP2 temperature [°C]

→

1) (

∑

)

Right side:

Average interphase voltage [V]

Left side:

Average phase current [A]

→

…………

Favorite indication display

Press the

key to change the display to the last registered combination of indicated value

display.

Three favorite indicated value displays can be saved.

Press the

key again to change to the second last registered favorite indicated value display.

Press the

key again to change to the third last registered favorite indicated value display.

Press the

key again to return to the last registered favorite indicated value display.

How to save the favorite indicated value display

Pair up the indicated value display in the desired combination.

Press the

key and the

key sequentially in order to save the new

indicated value display as a favorite.

* From the fourth time, the oldest save will be deleted and a new indicated value display will be

saved.

VOL

OUT

☆

－

☆

－

☆

－

☆

－

FUNC

－

Содержание UPM100


























































































Результаты поиска

Содержание UPM100

Отзывы:

Похожие инструкции для UPM100

Бренды по названию

Популярные бренды

Unipulse UPM100, Руководство по эксплуатации

Результаты поиска

Содержание UPM100

Отзывы:

Похожие инструкции для UPM100

Бренды по названию

Популярные бренды