3
C
C
C
C
Changing the cutting blade drive shaft
hanging the cutting blade drive shaft
hanging the cutting blade drive shaft
hanging the cutting blade drive shaft
hanging the cutting blade drive shaft
1.
Turn off carpet strip cutting machine.
2.
Move clutch lever down to touch position (B) .
3.
Open cover.
4.
Loosen tommy screw by hand until resistance is noticable.
5.
Pull notch (E), turn tommy screw in counterclockwise direction, release notch (E) and continue
turning until cutting blade drive shaft slightly clicks into place and the cutting blade drive shaft
flange is located at the right bulging of the bracket plate.
6.
Remove two allen screws with the wrench (delivered with the accessories) out of the bearing
housing and remove cutting blade drive shaft. Put in new cutting blade drive shaft, screw in
allen screws, fasten them lightly and turn tommy screw in counterclockwise direction until
cutting blade drive shaft faces the counter shaft and noticeable clicks into place.
7.
Fasten tommy screw by turning clockwise.
8.
Move clutch lever in position (A) upwards.
9
Close cover.
The press pads are designed to fit cutting widths of 60, 70 or 80 mm. Press pads are resilient and their
height do not have to be adjusted when cutting different rug thicknesses.
When using cutting widths differing from these sizes a complete press pad with the required strip
width has to be ordered.
Installation of press pad is relatively simple. Push in press pad traverse bar to the stop in the drilled
hole, after that adjust the press pads to be just in contact with the counter shaft and tighten with two
allen screws at the backside of the frame.
Make sure that the ground cut edge always points to the left.
Caution:
Caution:
Caution:
Caution:
Caution:
Carpet glue residues have to be removed from the grooves of the lower counter shaft daily. Plugged
Carpet glue residues have to be removed from the grooves of the lower counter shaft daily. Plugged
Carpet glue residues have to be removed from the grooves of the lower counter shaft daily. Plugged
Carpet glue residues have to be removed from the grooves of the lower counter shaft daily. Plugged
Carpet glue residues have to be removed from the grooves of the lower counter shaft daily. Plugged
up grooves can cause breakage of driving mechanism.
up grooves can cause breakage of driving mechanism.
up grooves can cause breakage of driving mechanism.
up grooves can cause breakage of driving mechanism.
up grooves can cause breakage of driving mechanism.
Cleaning of the lower counter shaft:
Cleaning of the lower counter shaft:
Cleaning of the lower counter shaft:
Cleaning of the lower counter shaft:
Cleaning of the lower counter shaft:
1.
1.
1.
1.
1.
Bring shaft carrier in intermediate position (shaft change position).
Bring shaft carrier in intermediate position (shaft change position).
Bring shaft carrier in intermediate position (shaft change position).
Bring shaft carrier in intermediate position (shaft change position).
Bring shaft carrier in intermediate position (shaft change position).
2.
2.
2.
2.
2.
Loosen two allen screws on backside of frame.
Loosen two allen screws on backside of frame.
Loosen two allen screws on backside of frame.
Loosen two allen screws on backside of frame.
Loosen two allen screws on backside of frame.
3.
3.
3.
3.
3.
Remove rod with press pads completely (pull out).
Remove rod with press pads completely (pull out).
Remove rod with press pads completely (pull out).
Remove rod with press pads completely (pull out).
Remove rod with press pads completely (pull out).
4.
4.
4.
4.
4.
Close cover, start carpet strip cutting machine and remove carpet and glue residue with the
Close cover, start carpet strip cutting machine and remove carpet and glue residue with the
Close cover, start carpet strip cutting machine and remove carpet and glue residue with the
Close cover, start carpet strip cutting machine and remove carpet and glue residue with the
Close cover, start carpet strip cutting machine and remove carpet and glue residue with the
cleaning hook (in asseccories) completely from the grooves.
cleaning hook (in asseccories) completely from the grooves.
cleaning hook (in asseccories) completely from the grooves.
cleaning hook (in asseccories) completely from the grooves.
cleaning hook (in asseccories) completely from the grooves.
