Product Brochure For W1542
Sydney: (02) 9890 9111
Brisbane: (07) 3715 2200
Melbourne: (03) 9212 4422
Perth: (08) 9373 9999
www.machineryhouse.com.au
Note: CUT MODE and GRIND MODE won’t be recorded.
MODES
The goggles have 4 function modes:
- WELD MODE (Shade range 5-9).
- WELD MODE (Shade range 9-13).
- GRIND MODE.
- CUT MODE.
In WELD MODE, 3 functions can be adjusted; Sensitivity, Shade and Delay.
Press the MODE button on the goggles to cycle between WELD MODE and CUT MODE. Within any mode, press and hold the GRIND button
for 2 seconds and release to change to GRIND MODE. Press and hold the GRIND button for 2 seconds and release to change back to
welding and cutting modes.
VARIABLE SHADE CONTROL
To change the shade in welding and cutting modes, press the SHADE button once and Icon 7 will start flashing. Once Icon 7 is flashing, press
the SHADE button again to cycle through the different shades.
Note: Choose an optimum Shade number for the required welding process or application (see back cover).
If the goggles do not darken when striking an arc, stop welding immediately and contact the UNIMIG service department.
SENSITIVITY CONTROL
The responsiveness to different light levels in various welding processes can be adjusted in the range 1-5 (from low to high). Sensitivity only
can adjusted be in welding modes.
To change the sensitivity in WELD MODE, press the SENS. button once and Icon 5 will start flashing. Once Icon 5 is flashing, press the
SENS. button again to cycle through the different shades.
1 (Low): The photo-sensitivity changes to be lower.
- Suitable for high amperage welding and welding in bright light conditions (lamp light or sun light).
5 (High): The photo-sensitivity changes to be higher.
- Suitable for low amperage welding and welding in poor light conditions.
- Suitable for welding with steady arc process such as TIG welding.
- Under normal use, a higher sensitivity setting is recommended.
DELAY CONTROL
The length of time delay for the goggles to return to a light state after welding can be adjusted in the range 1-5 (for 0.1-0.9s). The time delay is
for the protection of welder’s eyes from strong residual rays after welding.
To change the delay in WELD MODE, press the DELAY button once and Icon 6 will start flashing. Once Icon 6 is flashing, press the DELAY
button again to cycle through the different shades.
1 (0.1s): The time taken for the goggles to lighten after welding becomes shorter. The shortest time is about 0.1s depending upon welding
point temperature and shade set. This setting is ideal for track welding or production welding with short welds.
5 (0.9s): The time taken for the goggles to lighten after welding becomes longer. The longest time is about 0.9s depending upon welding point
temperature and shade set. This setting is ideal for welding at high amperage where there is an afterglow from the weld.
GRIND MODE SELECTION
Select GRIND mode by pressing and holding the “GRIND” button for 2 seconds and releasing, on the right side of the goggles. Icon 9 will
display when GRIND mode is active. An orange light on the inside of the goggles will also start to flash.
Note: Do not weld in the GRIND mode, the goggles will not darken.
CUT MODE SELECTION
Press the MODE button to cycle to the CUT MODE. Icon 8 will display when CUT mode is active.
To change the shade in CUT MODE, press the SHADE button once and Icon 7 will start flashing. Once Icon 7 is flashing, press the SHADE
button again to cycle through the different shades (5-8).
Note: Do not weld in the cutting mode.
Includes
•
UNIMIG Welding Goggle & Mask
•
UNIMIG ROGUE™ Welding Hood
•
2 x Spare Outer Lens
•
1 x Spare Inner Lens
•
Elastic Headband
•
LED Headlight
•
Goggles Carry Bag
Page 2 of 4
29/07/2021 6:14 AM
Specifications and prices are subject to change without notification
