Unimig KUMJR350K Скачать руководство пользователя страница 17

17

Mig Torch Liner Installation

(1)  Lay the torch out straight on the ground and remove the front end parts 

(2)   Remove the liner retaining nut.

(3)   Carefully pull the liner out of the torch cable assembly

(4)   Select the correct new liner and carefully unravel avoiding putting any kinks in the liner, if you kink the 

 

liner it will make it no good and will require replacement.

(5)   Carefully  and slowly feed the liner in short forward movements down the cable assembly all the way 

 

through and out the torch neck end. Avoid kinking the liner, kinking liner it will make it no good and  

 

require replacement. 

(6)   Fit the liner retaining nut and screw down only 1/2 way 

(7)   Leaving the torch straight snip the liner approximately 3mm past the end of the torch neck 

(8)   Place the tip holder over the end of the liner and screw into the torch neck nipping it up tight.

(9)   Screw down the liner nut the remaining 1/2 and nip it up tight.  This method compresses the liner  

 

inside the torch cable assembly preventing it moving during use and ensures good wire feed.

(2) Remove the liner retaining nut

(3) Carefully pull out and completely 

remove the liner

(4) Carefully unravel the new liner

(8) Replace the front end parts

(5) Carefully feed in the new liner down 

the torch lead all the way to exit the torch 

neck. 

(9) Fully screw down the liner retaining 

nut and nip it up tight.

(6) Fit the liner retaining nut and screw 

only 1/2 way down

(1) Remove mig torch front end parts

(7) Snip the liner off 3mm past the end 

of the torch neck.

Содержание KUMJR350K

















































Отзывы: