12
Cleaning and Care (continued)
3 . Disconnect gas cylinder per “Disconnecting Gas Cylinder” section .
4 . Remove cooking grids and heat plates .
5 . Remove burners by removing the fasteners, which secure the burners to the grill bottom .
6 . Lift burners up and away from gas valve orifice .
7 . Disconnect wire from spark electrode .
8 . Clean venturi of each burner with small bottle brush or compressed air .
9 . Remove all food residue and dirt on burner surfaces .
10 . Clean any clogged ports with a stiff wire (such as an opened paper clip) .
11 . Inspect burners for any damage (cracks or holes) . If damage is found, replace with new burner(s) from manufacturer .
12 . Reinstall burners, checking to insure that gas valve orifice is correctly positioned inside each burner/venturi tube . Also, check position of spark
electrode .
13 . Replace heat plate(s) and cooking grid(s) .
14 . Connect gas cylinder per “Installing Gas Cylinder” section .
15 . Perform leak test per “Checking for Leaks” section .
Cleaning Side Burner
1 . Turn the regulator valve handle counterclockwise into the the “OFF” position . (Figure C) .
2 . Turn all control knobs clockwise to the
•
(OFF) position .
Note: A “poof” sound is normal as the last of the gas is burned .
3 . Disconnect gas cylinder per “Disconnecting Gas Cylinder” section .
4 . Remove side burner grid .
5 . Remove burner by removing the screws that secure the burner to the side shelf .
6 . Lift burner up and away from gas valve orifice .
7 . Clean venturi of burner with small bottle brush or compressed air .
8 . Remove all food residue and dirt on burner surface .
9 . Clean any clogged ports with a stiff wire (such as an opened paper clip) .
10 . Inspect burner for any damage (cracks or holes) . If damage is found, replace with new burner from manufacturer .
11 . Reinstall burners, checking to insure that gas valve orifice is correctly positioned inside each burner/venturi tube . Also, check position of spark
electrode .
12 . Replace cooking grid(s) .
13 . Connect gas cylinder per “Installing Gas Cylinder” section .
14 . Perform leak test per “Checking for Leaks” section .
Before Storing
1 . Turn the regulator valve handle counterclockwise into the the “OFF” position (Figure C) .
2 . Turn all control knobs clockwise to the
•
(OFF) position .
Note: A “poof” sound is normal as the last of the gas is burned .
3 . Disconnect gas cylinder per “Disconnecting Gas Cylinder” section .
4 . Clean all surfaces .
5 . Lightly coat the burner(s) and cooking grid(s) with cooking oil to prevent excess rusting .
6 . If storing the grill indoors, disconnect the gas cylinder per “Disconnecting Gas Cylinder” section .
7 . Place the protective cap cover on the gas cylinder and store the tank outdoors in a well-ventilated area out of direct sunlight .
8 . If storing the grill indoors, cover the grill and store in a cool dry place .
9 . If storing the grill outdoors, cover the grill with a grill cover for protection from the weather .
Figure 8
Burner Flame Conditions
Use this chart to see if your burners
need to be cleaned .
1-2 in. /
25.4 - 50.8 mm
Normal:
Soft blue flames with yellow
tips between 1 in . - 2 in . height .
Needs cleaning:
Noisy with hard
blue flames .
Has to be replaced:
Wavy with
yellow flames .
Specifications
Approvals
0359-16
Pin: 0359CR01461
Barbecue
Appliance Category
I
3+
Weight
33 .5 kg / 73 .8 lbs
Dimensions (L x W x H)
138cm x 62cm x 118cm
Grilling surface (L x W)
73 .0cm x 42 .0cm
Load weight
Side shelf
Side burner table
Max . 15 kg .
Max . 15 kg .
Gas System
Heat quantity
Main burner
Side burner
14 .08 kW (48,000 BTU)
3 .52 kW (12,000 BTU)
Mass flow rate
17 .6 kW (1256 g/h)
Gas type
Butane
Propane
Pressure regulator
Flow rate
Operating pressure
Preset and
– approved pressure regulator
Max . 1 .5 kg/h
28-30 mbar Butnae / 37 mbar Propane
Gas cylinder
Standard gas cylinder with a fill weight of 11 or 15 kg
Gas hose
approved hose (Max 1 .5 m)
Ignition type
Integrated ignition
Flame regulation
Infinitely adjustable 1 - max .
Nozzle diameter
0 .92mm main / 0 .92mm side
Refund information
28 day no quibble refund . If you’re not delighted by your product, simply bring it back within 28
days for a no quibble refund . Don’t forget to include all of the item’s original components and
packaging along with your receipt or other proof of purchase .
Customer Services Information
If you require further information or advice regarding your product or experience any problems
please contact customer services at the telephone number or address below . When calling or
writing please quote the product spec code or model number . Spec Code: 16B .02 .17 .031,
16B .02 .17 .032, 16B .02 .17 .033
Contact Us
Customer Services: 0800 9520101
Visit our website: www .asda .com
Produced for ASDA Stores Ltd, Southbank, Great Wilson Street, Leeds, LS11 5AD
