Outdoor LP Gas Barbecue Grill Model No. GBC1030WRS-C
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Installing LP Gas Tank
To operate you will need (1) precision-filled standard grill LP gas
tank (20#) with external valve threads.
Note:
An empty standard grill LP gas tank weighs approximately
18 lbs. A precision-filled standard grill LP gas tank should weigh
no more than 38 lbs.
CAUTION: LP gas tank must be properly
disconnected and removed prior to moving this
grill.
Insert LP Gas Tank
Place precision filled LP gas tank upright into the notches in the right cart frame so the tank
valve is facing the gas line connection.
Secure LP Gas Tank
Secure tank by sliding tank retainer wire over shoulder of LP gas tank.
Connect LP Gas Tank
Before connecting, be sure that there is no debris caught in
the head of the LP gas tank, head of the regulator valve or
in the head of the burner and burner ports.
Connect regulator/hose assembly to tank by turning knob
clockwise until it stops.
Disconnect LP Gas Tank
Before disconnecting make sure the LP gas tank valve is
“CLOSED”.
Disconnect regulator/hose assembly from LP gas tank by
turning knob counterclockwise until it is loose.
CAUTION: LP gas tank must be properly
disconnected and removed prior to moving
this grill.
Need a tank of gas?
Try tank exchange service. It’s easy, fast, safe,
and available at tens of thousands of conveniently located retail outlets
nationwide. You can purchase a new full tank or exchange your empty for
a precision filled one.
Operating Instructions
Checking for Leaks
Burner Connections
1. Make sure the regulator valve and hose connections are securely fastened to the burner and
the tank.
If your unit was assembled for you, visually check the connection between the burner venturi
pipe and orifice. Make sure the burner venturi pipe fits over the orifice.
WARNING: Failure to inspect this connection or follow these
instructions could cause a fire or an explosion which can cause death,
serious bodily injury, or damage to property.
2. Please refer to diagram for proper installation. (Figures 1 and 2)
3. If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for
assistance.
Tank/Gas Line Connection
1. Make 2-3 oz. of leak solution by mixing one part
liquid dishwashing soap with three parts water.
2. Make sure control knobs are “OFF ” position.
(Figure 3)
3. Connect LP gas tank per “Installing LP Gas Tank”
section.
4. Turn LP gas tank valve to “OPEN”.
5. Spoon leak check solution at all “X” locations
(Figures 1, 2 and 4)
a. If any bubbles appear turn LP gas tank valve to
“CLOSED”, reconnect and re-test.
b. If you continue to see bubbles after several
attempts, turn LP gas tank valve to “CLOSED” and
disconnect LP gas tank, per “Disconnect LP Gas
Tank” instructions, and contact 1.800.762.1142
for assistance.
c. If no bubbles appear after one minute turn LP gas
tank valve to “CLOSED”, wipe away solution and
proceed.
Operating Main Burners
First Use
1. Make sure all labels, packaging and protective films
have been removed from the grill.
2. Remove manufacturing oils before cooking on this
grill for the first time by operating the grill for at
least 15 minutes on (HIGH) with the lid closed. This
will “heat clean” the internal parts and dissipate
odors.
Lighting Instructions
Caution: Keep outdoor gas cooking
appliance area clear and free from
combustible materials, gasoline and
other flammable vapors and liquids.
Caution: Do not obstruct the flow of
combustion and ventilation air.
Caution: Check and clean burner/
venturi tubes for insects and insect
nests. A clogged tube can lead to a fire
beneath the grill.
Caution: Attempting to light the burner
with the lid closed may cause an
explosion.
1. Open lid.
2. Make sure there are no obstructions of airflow to
the burners. Spiders and insects can nest within
and clog the burner / venturi tube at the orifice. A
clogged burner tube can lead to a fire beneath the
appliance.
3. All control knobs must be in the “OFF ” position. (Figure 3)
4. Connect LP gas tank per “Installing LP Gas Tank” section.
5. Turn LP gas tank valve to “OPEN”.
6. Select burner to light. Push and turn control knob to (HIGH).
7. Press the (electronic igniter) button and hold for up to 5 seconds to light burner.
8. If ignition does not occur in 5 seconds, turn burner control knob “OFF ”, wait 5 minutes, and
repeat lighting procedure.
Figure 1
XX
Burner
venturi
pipe
LP Gas Valve
Connection
LP Gas
Valve with
Orifice
Main Burners
Figure 2
XX
LP Gas
Connection
LP Gas Valve
with Orifice
Side Burner
Burner
venturi
pipe
Figure 3
OFF
ARRÊT
Figure 4
X
X
X
X
X
