Uniden uh078sx Скачать руководство пользователя страница 27

Страница: 27 / 28

WARRANTY

UNIDEN UH078SX UHF CB TRANSCEIVER RADIO

Two Year Limited Warranty

Note:

Please keep your sales docket as it provides evidence of warranty.

Warrantor:

Uniden Australia Pty Limited ABN 58 001 865 498 Uniden New Zealand Limited

Warranty only available in original country of purchase

Elements of Warranty:

Uniden warrants to the original retail owner for the duration of this

warranty, its uh078sx UHF CB Transceiver Radio (hereinafter referred to as the Product)

to be free from defects in materials and craftsmanship with only the limitations or

exclusions set out below.

Warranty Duration:

This warranty to the original retail owner only, shall terminate and be

of no further effect TWO (2) years after the date of original retail sale. This warranty will

be deemed invalid if the Product is;

(A) Damaged or not maintained as reasonable and necessary,

(B) Modified, altered or used as part of any conversion kits, subassemblies, or any

configurations not sold by Uniden,

(D) Repaired by someone other than an authorized Uniden Repair Agent for a defect or

malfunction covered by this warranty,

(E) Used in conjunction with any equipment or parts or as part of a system not

manufactured by Uniden, or

(F) Where the Serial Number label of the product has been removed or damaged beyond

recognition.

Warranty only valid in the country of original retail/sale.

Parts Covered

: This warranty covers for

, the Product and included

accessories.

Statement of Remedy:

In the event that the Product does not conform to this warranty at

any time while this warranty is in effect, the warrantor at its discretion, will repair the

defect or replace the Product and return it to you without charge for parts or service. This

warranty does not provide for reimbursement or payment of incidental or consequential

damages.

This EXPRESS WARRANTY is in addition to and does not in any way affect your rights

under the TRADE PRACTICES ACT 1974 (Cth) (Australia) or the CONSUMER

GUARANTEES ACT (New Zealand).

Procedure for obtaining performance of warranty

: In the event that the Product does

not conform to this warranty, the Product should be shipped or delivered, freight prepaid,

with evidence of original purchase, (eg. a copy of the sales docket) to the warrantor at:

UNIDEN AUSTRALIA PTY

LIMITED UNIDEN NEW ZEALAND LTD

Service Division

345 Princes Highway,

150 Harris Road, East Tamaki,

Rockdale NSW 2216

Auckland

Fax (02) 9599 3278

Fax (09) 274 4253

www.uniden.com.au

www.uniden.co.nz

Customers in other states should ship or deliver the Product freight pre-paid to the

nearest Uniden Authorized Repair Centre. (Contact Uniden for the Warranty Agent

nearest you.)

TWO (2) years

Содержание uh078sx





























Результаты поиска

Содержание uh078sx

Отзывы:

Похожие инструкции для uh078sx

Бренды по названию

Популярные бренды

Uniden uh078sx, Руководство по эксплуатации

Результаты поиска

Содержание uh078sx

Отзывы:

Похожие инструкции для uh078sx

Бренды по названию

Популярные бренды