background image

Operation

5

UHF CB Transceiver

UNIDEN UH064SX-2NB

Power On/Off

1.   Press and hold 

SELECT

 /   key to turn the radio on.

    A channel number will appear on the display.
2.   Press and hold 

SELECT

 /   key to turn the radio off.

Volume

Press   or   key to increase or decrease the

volume level. ‘VOL’ icon appears on the display

while volume is being adjusted.

There are 8 volume levels. Level 0 (No Audio) to

Level 7 (Maximum Volume).

Adjusting the Key Beeps

Your radio emits a beep each time one of the keys

(except for the PTT key) is pressed.

1.   To turn OFF this beep: Press and hold 

 / 

CALL

 key while turning  

    on the radio.

2.   To turn ON this beep: Press and hold 

 / 

CALL 

key while turning  

    on the radio.

Roger Beep

Roger Beep is a BEEP that is sent to notify the end of transmission (both PTT 

and VOX transmission.) Roger Beep can be heard through the speaker when 

Key Beep is on. Roger Beep is transmitted even if Key Beep is turned off.

However, Roger Beep will not be heard from the speaker.

1. To turn OFF Roger Beep: Press and hold   key while turning on the radio.

2. To turn ON Roger Beep: Press and hold   key while turning on the radio.

Keylock On/Off

1. Press 

 / 

CALL 

key for 1.5 seconds to enter keylock on mode.

2. Press 

 / 

CALL 

key for 1.5 seconds while in Keylock mode to exit  

  the Keylock mode.

NOTE

While in Keylock on mode, the UH064SX-2NB can still 

receive and transmit.

Содержание UH064SX-2NB

















Отзывы: