PAGE
5
PAGE
4
Each handset must have a DIFFERENT
handset ID number. If any two handsets have
the same ID number, the entire system will
not function properly.
PROGRAMMING THE
HANDSET ID
TURNING THE RINGER
ON/OFF (L1 Ring)
NOTE:
■
When the ringer is set to “Off”, an icon will display
to alert you that the handset will not ring during
incoming calls.
BASIC PROGRAMMING
1
3
2
Press
PRG
.
Press
▲
or
▼
until “
Handset ID
”
displays.
Press
“#”
to begin programming the
Handset ID.
4
5
Enter a selected 2-digit station ID
number (choose any number from
11-70).
Press
OFF
or
PRG
to end the
programming session OR press
▲
or
▼
to advance to another
programming step.
1
3
2
4
5
You can turn the ringer on or off on each
handset.
Press
PRG
.
Press
▲
or
▼
until “
L1 Ring
”
displays.
The current setting will be displayed
on the second line of the display.
Press
“#”
to toggle between “On” and
“Off”.
When the desired setting is displayed,
press
OFF
or
PRG
to end the
programming session OR press
▲
or
▼
to advance to another
programming step.
1
3
2
4
RINGER TYPE
PROGRAMMING
The unit allows you to select one of four ring
tones for each handset. The ringer type
default is set to type 1.
Press
PRG
.
Press
▲
or
▼
until “
Ring Type
”
displays.
Press
“#”
to toggle between any one
of the four ring tones. Each time you
make a selection, you will hear the
corresponding ringer sound.
When the desired ringer type is
displayed, press
OFF
or
PRG
to end
the programming session OR press
▲
or
▼
to advance to another
programming step.
All handsets must be programmed with the
SAME security code (Sec. Code) in order to
operate as a system. The first handset that is
programmed must be registered to the base
(see instructions below). Additional handsets
need only be programmed with the same
security code to begin operation.
2
1
Press
PRG
(Program).
Press
▲
or
▼
(located on the side of
the handset) until “
Sec Code
”
displays.
3
Enter
“#”
to begin programming the
security code.
4
Using the keypad, enter any 6 digit
code.
5
Press
OFF
or
PRG
to end the
programming session OR press
▲
or
▼
to advance to another
programming step.
REGISTERING THE
HANDSET TO THE BASE
If you are programming the FIRST handset in
the system, you must register the new system
security code to the base unit.
1
Position the handset close (within 6-8
inches) to the base.
2
Press
PRG
.
3
Press
▲
or
▼
until “
REGISTER HS
to Base
” displays.
4
Press and hold
PAGE
on the base unit
for at least 3 seconds. The light will
begin to flash.
5
Release
PAGE
.
SYSTEM REGISTRATION
(SECURITY CODE)
PROGRAMMING THE
SYSTEM SECURITY CODE
NOTE:
■
Once you choose a security code for the first
handset, you must use the SAME code for each
additional handset. Don’t worry about forgetting
the code- it can be displayed on the handset to
remind you of the code when you add additional
handsets.
NOTE:
■
Make sure you don’t confuse the System Security
Code with the Handset ID number. Each handset
must have the SAME System Security Code, but
they must have DIFFERENT Handset ID numbers.
6
Press
“#”
on the handset. Keep
holding
“#”
until a confirmation beep
is heard.
NOTE:
■
You don’t need to hold both buttons (PAGE and
“#”) at the same time. After you press and release
the PAGE button, then press the “#” button until
you hear the confirmation beep. If you don’t hear
the beep after about 15 seconds, try repeating the
steps again.
7
Press
OFF
or
PRG
to end the
programming session OR press
▲
or
▼
to advance to another
programming step.
Ring: Mid
ID: 11
Содержание 1660
Страница 15: ...PAGE 28 HANDSET FEATURES ...
