
26
Soc et
pressure
OUTPUT
The following instructions are intended
excl usive ly for
Unical AG Sp.A. author-
ised service personnel.
1) Maximum output adj ustment
- Operate the b oiler in “ calib ration” mode at MAXI-
MUM OUTP UT ( see 3.11.1).
- Once the b urner is on check that the “ MAXIMUM”
pressure va lue corresponds to that indicated in
the tab le “ NOzzlES - P RESSURE” .
- Should it not correspond, correct it b y removi ng
the screw cap
‘’Q’’
and turning screw
“S”
b elow
ClOCKW
ISE to increase it, ANTIClOCKW
ISE
to decrease it.
3) Conclusion of the b asic calib rations
- once the gas v alv e minimum and max imum pres-
sure va lues are checke d and top-up is required
( points 1-2):
- disab le the timed “ calib ration” function b y switch-
ing off the
main
switch.
- Remove the fle ible tube from the pressure
gauge and close the pressure soc et screw
again.
-
Chec that there are no gas lea s.
P
Q
R
P
R
Q
S
3.12 - ADJ USTING THE BURNER
2) Minimum output adj ustment
- Operate the b oiler in “ calib ration” mode at MINI-
MUM OUTP UT ( see 3.11.1)
- Once the b urner is on, check that the “ MINIMUM”
pressure v alue corresponds to that indicated in the
tab le “ NOzzlES - P RESSURE” .
- Correct it if needed b y turning ( with a screwdriv er)
the screw
“R”;
ClOCKW
ISE to increase it, ANTI-
ClOCKW
ISE to decrease it.
All b oilers leave the factory already cali-
b rated and tested, howeve r in the eve nt
the gas va lve recalib ration is required:
- loosen the needle screw
‘’P’’
located inside the
pressure socke t at gas va lve outlet and connect
a pressure gauge with reference to the figure.
- Check the supply pressure va lue ( see NOzzlES
- P RESSURES tab le).
S
P
Attention, during these operations do
not ta e an samples in domestic hot
w ater mode.
www.unicalag.ru
The following instructions are intended
The following instructions are intended
p.A. author
p.A. author
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
ClOCKW
ISE to increase it, ANTIClOCKW
ISE
ClOCKW
ISE to increase it, ANTIClOCKW
ISE
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
Q
R
2) Minimum output adj ustment
2) Minimum output adj ustment
Operate the b oiler in “ calib ration”
Operate the b oiler in “ calib ration”
mode at MINI
mode at MINI
MUM OUTP UT ( see 3.11.1)
MUM OUTP UT ( see 3.11.1)
Once the b urner
Once the b urner
is on, check that the “ MINIMUM”
is on, check that the “ MINIMUM”
pressure v alue corresponds to that indicated in the
pressure v alue corresponds to that indicated in the
tab le “ NOzzlES - P RESSURE” .
tab le “ NOzzlES - P RESSURE” .
-
-
Co
Co
rrect it if needed b y turning ( with a screwdriv er)
rrect it if needed b y turning ( with a screwdriv er)
the screw
the screw
“R”;
“R”;
ClOCKW
ISE to increase it, ANTI
ClOCKW
ISE to increase it, ANTI
ClOCKW
ISE to decrease it.
ClOCKW
ISE to decrease it.
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
S
www.unicalag.ru
www.unicalag.ru
P
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
www.unicalag.ru
Содержание !DEA CS 24 el
Страница 37: ...w w w u n i c a l a g r u ...
Страница 73: ...37 w w w u n i c a l a g r u ...
Страница 74: ...38 w w w u n i c a l a g r u ...
Страница 75: ...w w w u n i c a l a g r u ...