Uniblitz Vincent Associates VMM-D3 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 38

Uniblitz Vincent Associates VMM-D3 Скачать руководство пользователя страница 17

VMM-D3/D4 Shutter Driver

15

VMM-D3/VMM-D4 Rear Panel Operator Controls

Please refer to Figure 4 for

VMM-D3

and

VMM-D4

rear panel layouts, respectively. Please note

that both units’ rear panels are identical.

1.

One 3-conductor IEC type power receptacle AC Input module containing:
115VAC/230VAC line voltage indicator, fuses, and power On/Off switch.

2.

One 6 conductor pluggable terminal strips labeled OUTPUT CONTROL. Uses 5V-
TTL logic.

3.

One 6 conductor pluggable terminal strips labeled INPUT CONTROL. Uses 5V-TTL
logic.

4.

Four Energy Select HI/LO slide switches to allow operation with 35 mm and larger
aperture shutter types.

Note: Channel 4 is disabled on the

VMM-D3

only.

5.

Four 7-pin SHUTTER connectors, 1 per shutter.

Note: Channel 4 is disabled on the

VMM-D3

only.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
15
16
17
18
19
...
»

Содержание Vincent Associates VMM-D3







































Отзывы:

Нет отзывов