UNI-T UTG9000T Series Скачать руководство пользователя страница 10

Страница: 10 / 162

UTG9000T Series Function Abitrary Waveform Generator

Chapter 1 Safety Information

1.1 Terms and symbols

Terms in the manual
The following terms may used in the manual

WARNING:

Warning statement, identifing conditions and and procedures that are dangerous to

the user.

CAUTION:

Cautionary statement, identifing conditions and procedures that may cause damage

to the product and other properties.

Terms on the product
The following terms may used on the product:

DANGER:

Indicates an injury or hazard that may immediately happen.

WARNING:

Indicates an injury or hazard that may not immediately happen.

CAUTION:

Indicates that a potential damage to the instrument or other property might occur.

Symbols on the product
The following symbols may used on the product

Measuring ground terminal

Frame ground terminal

ON/OFF

Danger

！

High voltage

Caution, consult the user’s manual

Protective ground terminal

Conforms to European Union directivies

Certified by CSA Group to North American safety standards

C-tick is registered trademark of Spectrum Management Agency of Australia. It indicates

conformity with provisions of Australian EMC Framework formulated according to terms of

Wireless Communication

Act

in 1992.

Содержание UTG9000T Series



































































































































































Результаты поиска

Содержание UTG9000T Series

Отзывы:

Бренды по названию

Популярные бренды

UNI-T UTG9000T Series, Руководство пользователя

Результаты поиска

Содержание UTG9000T Series

Отзывы:

Бренды по названию

Популярные бренды