background image

Service Manual                                                                                                                                                                                                                                            UTG1000X Series 

Instruments.uni-trend.com                                                                                                                                                                                                                               

 

3

 / 

20

 

 

 

1.

 

Overview 

 

Safety Information 

This section contains information and warnings that must be observed to keep the instrument operating 
under appropriate safety conditions. In addition to the safety precautions indicated in this section, you must 
follow generally accepted safety procedures. 

 

 

Safety Precautions 

Warning

 

To avoid possible electric shock and personal safety, follow these guidelines: 

During all phases of operation, service, and repair of this instrument, the following 
general safety precautions must be followed. Unilever will not bear any responsibility 
for the personal safety and property loss caused by the user's failure to follow the 
following safety precautions. This equipment is designed for professional users and 
responsible institutions for measurement purposes. 
Do not use this equipment in any manner not specified by the manufacturer. Unless 
otherwise specified in the product documentation, this equipment is for indoor use 
only. 

 
 
 
 

Safety statement 

Warning 

The WARNING statement indicates a hazard. It alerts the user to a certain procedure, 
method of operation, or similar situation. Personal injury or death could result if the 
rules are not performed correctly or followed. Do not proceed to the next step until the 
conditions of the indicated WARNING notice are fully understood and met. 

Caution 

The "Caution" symbol indicates a hazard. It alerts the user to a certain procedure, 
method of operation, or similar situation. Failure to perform or follow the rules 
correctly may result in damage to the product or loss of important data. Do not proceed 
to the next step until the indicated CAUTION conditions are fully understood and met. 

Notice 

The “Notice” statement indicates important information. Prompting the user's attention 
to a procedure, practice, condition, etc., should be prominently displayed. 

 
 
 
 
 
 
 

Содержание UTG1000X Series





















Отзывы: