UNI-T utd2000 Скачать руководство пользователя страница 65

Страница: 65 / 65

UTD2000 Series User Manual

years from the date of shipment by

the authorized dealer. If any such product proves

defective during this

warranty period, UNI-T will repair the defective product or provide a

replacement according to specific terms and conditions of the warranty.

To request

maintenance and repair service or a full copy of the

warranty, please contact your nearest

UNI-T sales and

maintenance office.

Save and except the guarantee given herein or in other applicable

warranty, UNI-T makes

no other express or implied guarantee, including but not limited to any implied guarantee

on the product's tradability and suitability for any specific purpose. Under no circumstance

will UNI-T bear any liability for any indirect, special or subsequent loss.

Appendix D Contact Us

For product support outside China, contact your local UNI-T supplier or sales centre.

Service Support: Many UNI-T products offer optional plans of extended warranty period or

calibration period. For details please contact your

local UNI-T supplier or sales centre.

Содержание utd2000


































































Результаты поиска

Содержание utd2000

Отзывы:

Похожие инструкции для utd2000

Бренды по названию

Популярные бренды

UNI-T utd2000, Руководство пользователя

Результаты поиска

Содержание utd2000

Отзывы:

Похожие инструкции для utd2000

Бренды по названию

Популярные бренды