UNI-T UT50D Скачать руководство пользователя

Страница: 5 / 36

Safety Information

This Meter complies with the standards IEC61010: in
pollution degree 2, overvoltage category (CAT. II 1000V,
CAT. III 600V) and double insulation.

CAT. II: Local level, appliance, PORTABLE EQUIPMENT
etc., with smaller transient voltage overvoltages than
CAT. III
CAT. III: Distribution level, fixed installation, with smaller
transient overvoltages than CAT. IV

Use the Meter only as specified in this operating manual,
otherwise the protection provided by the Meter may be
impaired.

In this manual, a Warning identifies conditions and actions
that pose hazards to the user, or may damage the Meter
or the equipment under test.

A Note identifies the information that user should pay
attention on.

International electrical symbols used on the Meter and
in this Operating Manual are explained on page 8.

Model UT50D: OPERATING MANUAL

Содержание UT50D





































Результаты поиска

Содержание UT50D

Отзывы:

Похожие инструкции для UT50D

Бренды по названию

Популярные бренды

UNI-T UT50D, Руководство по эксплуатации

Результаты поиска

Содержание UT50D

Отзывы:

Похожие инструкции для UT50D

Бренды по названию

Популярные бренды