UNI-T UT202A Скачать руководство пользователя страница 3

Страница: 3 / 25

Safety Information

This Meter complies with the standards

IEC61010: in pollution degree 2, overvoltage

category (CATII 600V, CAT III 300V) and double

insulation.

CATII: Local level, appliance, PORTABLE

EQUIPMENT etc., with smaller transient

overvoltages than CATIII.

CAT III: Distribution level, fixed installation, with

smaller transient overvoltages than CAT IV

Use the Meter only as specified in this operating

manual, otherwise the protection provided by

the Meter may be impaired.

In this manual, a Warning identifies conditions

and actions that pose hazards to the user, or

may damage the Meter or the equipment under

test.

A Note identifies the information that user

should pay attention to.

International electrical symbols used on

the Meter and in this Operating Manual are

explained on page 6.

UT202A Operating Manual

Содержание UT202A


























Результаты поиска

Содержание UT202A

Отзывы:

Похожие инструкции для UT202A

Бренды по названию

Популярные бренды

UNI-T UT202A, Руководство по эксплуатации

Результаты поиска

Содержание UT202A

Отзывы:

Похожие инструкции для UT202A

Бренды по названию

Популярные бренды