6
•
This machine is mainly used with water mixing paint types. Other type of paints and paint thinners contain
dangerous, explosive or corrosive chemicals.
Multi-stage centrifugal compressor.
•
This compressor is equipped with double-insulation to improve the operational safety. Your compressor
does not need to be grounded.
•
The power source voltage (wall outlet) must be the same as shown on the specification label of your machine.
•
The switch (4) must be in position 0.
•
Connect the power cable (3) to extension cable with minimum rating of 1,200 W.
•
Connect the hose (2) to the multi-stage compressor (1), see pic. 2.
Using your machine.
•
Read the safety instructions carefully.
•
Switch on the switch (4) to activate the diffuser (or the multi-stage compressor).
Type of paints and used materials.
•
This Easy painter machine may be used with paints with viscosity between 10 - 35 (35 DIN-S).
•
Higher viscosity paints may be used ONLY with water diluted paints designed for OUTER AND INNER
WALL painting applications. THE QUALITY AND TYPE OF THE PAINT PLAY A VERY IMPORTANT ROLE
IN THE FINAL RESULTS.
The important and most common viscosity values are shown below:
•
Filling agent
10 - 20 no dilution
•
Organic paint
15 - 35 no dilution
•
Two- component paint, oil based paint
20 - 35
see the manufacturer instructions
•
•
Paint manufactures usually specify the dilute ratio in %: it is usually true for brush and roll-on painting jobs.
paint must be diluted (before diluting the entire paint container, test the dilute ratio with small amount of paint).
Viscosity
•
Viscosity is a technical term, telling you how thin or how thick the paint consistency is. In the first case the
viscosity is low and in the other case the viscosity is high.
•
Viscosity is measured in seconds.
•
Fill the supplied viscosity meter (6) with the paint, as seen on pic. 1 and observe and record how long it
will take for the paint to run out.
•
The measured value is the viscosity value expressed in DIN-S.
Paint preparation
•
Shake well.
•
Use a wooden stick for mixing.
•
OPERATION
Pour the paint in the paint tank of the spraying pistol (92) till it reaches 3/4 of the maximum tank volume.
If the paint is used in spray gun the percentage must be higher. It is good idea to tell the paint manufacturer /
(ranges between 5 - 50%).
See the manufacturer instructions regarding the type and the amount of required paint thinner in %
supplier that you will use his product in HVLP spraying pistol (High volume and low pressure). In such case the
11
Changing the tank seal (88) and (86):
•
Unscrew the hexagonal nut (90).
•
Remove the cover (89), located below the nut.
•
Remove the seal (88).
CAUTION: during the assembly of the cover, make sure the position of the seal (86) is correct.
Lubrication
Lubricate working surfaces with suitable grease regularly.
When the operational life of your device is over, dispose off it in accordance with valid rules and regulations.
Your product is made of metal and plastic parts that may be recycled when separated.
1. Disassemble all parts.
2. Separate all parts according to the material they are made of (e.g. metals, rubber, plastics, etc.).
Take the separated parts to the recycling facility near you.
3. Electrical waste (used electrical power tools, electric motors, recharging equipment, electronics,
accumulators, batteries etc.).
Dear customer. In accordance with the valid regional rules and regulations describing the management of
electrical waste, electrical waste is considered dangerous.
Disposal of electrical waste must be therefore handled as dangerous waste in accordance with waste
management rules valid in the state you are in.
It is prohibited to mix electrical waste with regular household waste.
You may return your used electrical appliance to a recycling facility near you. More information about
electrical and dangerous waste disposal may be obtained from your local authority or from the Internet.
If the machine breaks down, send it back to the vendor for quick repair.
Please, enclose brief description of the defect. That makes repair easier. If the machine is still covered by
warranty, enclose the warranty card and proof of purchase receipt. After the warranty period expires, we
repair your machine for a special price.
To prevent possible damages during shipping, packed the machine carefully or use the original packaging
material. We are not liable for shipping damages due to incorrect packaging of your machine. If making
a claim at the shipping company the level and method of packaging plays a major role during claim evaluation
process.
Note:
Pictures and contents in this manual may slightly differ from the actual product or accessories.
It is due to continuous improvement of our products. Such small differences have no effect on the product
functionality.
DISPOSAL
CAUTION
