Introduction:
Congratulations on the purchase of your new thru hull light (
Patent Pending
). Underwater Lights
®
USA, LLC takes pride in
providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These
lights can be installed in your vessel for aesthetics, to attract fish, for security and safety.
General Operating Information:
The 150W, HID, gas discharge lamp used in this light is not an instant re-strike lamp. This means that it must be allowed to cool
for approximately 10 to 20 minutes after being shut off before being restarted. HID lamps generally require approximately 2
minutes to reach full brightness and should be left on for a minimum of 10 minutes. Failure to do so may cause the lamp to flicker
when it is turned on the next time.
The light can be operated for a brief period of time when the vessel is out of the water, but, it is crucial that the vessel is in the
water to ensure proper lamp cooling, however, the light can be operated while the vessel is underway.
The main body is designed and tested to act as a cofferdam for added security.
Depending upon water clarity conditions, the light beam can reach up to 30 meters (100 feet).
General Safety Information:
This light is intended for use on fiberglass and wood hulled vessels.
Never try to install or remove this light while the vessel is in the water.
High temperature silicone electrical cable must be used between the light and the ballast, standard ships cable can be used from
the A/C power source to the ballast.
The body of the light must be electrically joined to the vessels grounding and cathodic protection system. Failure to do so may
cause corrosion.
Always disconnect and lock-out power before working on light.
The light should be visually inspected every six months.
The light electrical cabling and ballast box should be visually inspected for proper operating condition every six months.
Marine growth should be removed from the glass using a soft brush to allow both heat and illumination to exit the light.
Technical Specifications:
Lamp = 150 Watt - Metal halide - 12,000 Lumens - 7500 Kelvin color temperature - Approximately 3,000 hours life
Glass = Borosilicate glass - 12.7mm (0.5”) thick - 58mm (2.3”) diameter net aperture
Dimensions = 130mm (5.12”) diameter x 203mm (8.0”) long - 3.5 kilograms (8 pounds)
Construction = Marine bronze - Black anodized marine aluminum alloy
Power supply = 120VAC 50/60Hz input, 1.33 Amps - Minimum operating temperature -30°C (-22°F)
OR
Power supply = 240VAC 50/60Hz input, 0.59 Amps - Minimum operating temperature -30°C (-22°F)
Troubleshooting:
Please contact our technical support staff in Florida at 1-954-760-4447, Monday to Friday from 8:00 am to 5:00 pm EST.
Warranty:
Underwater Lights
®
USA, LLC warrants this light to be free from defects in workmanship and materials for a period of two years
from the date of original purchase (except lamps). Further, misuse, abuse, improper installation, neglect, improper shipping,
damage caused by disasters such as fire, flood and lightning, unauthorized repair or modifications will void said warranty. Should
your light prove defective during the warranty period, promptly contact Underwater Lights
®
USA, LLC for an RMA number and then
return the light freight prepaid with the RMA number clearly marked on the outside of the shipping container.
Underwater Lights Europe Sarl
16, rue Rouaze
06400 Cannes, France
Phone: 33-(0)-4-97-21-02-96
Fax: 33-(0)-4-97-21-10-96
Internet: www.seavision.com
Underwater Lights USA, LLC
3406 SW 26th Terrace, C-6/7
Fort Lauderdale, FL 3331
2
USA
Phone: 1-954-760-4447
Fax: 1-954-525-3261
Internet: www.seavision.com
Email: [email protected]
DOC:101205-14
Email: [email protected]
SV10 Light
120VAC/150W
240VAC/150W
