UMA Solar HC-10.5 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 35

background image

INSTALLATION MANUAL HELIOCOL

®

SOLAR POOL HEATER

NOTE:

All four corners of each row of panels should be securely fastened to the roof. The corners should already be

secured with the gator clamps or pipe straps on the plumbing lines connected to the feed and return lines. The top corner

opposite the return corner should already be secured by the panel mounting hardware.

The above photo (left) shows the return line attached to

the top header and an end cap on the bottom header.

The photo insert (center) the return line connection in

detail.

The above photo (right) shows the feed line attached

to the bottom header and an end cap attached to the

top header.

NOTE:

Be sure to support all of the weight of the plumbing with gator clamps or pipe straps. The mounting hardware is

not designed to support the weight of the plumbing in addition to the weight of the collectors.

12. Running the Feed & Return Lines

From Roof to Ground Level.

- Cont.

RUNNING THE FEED & RETURN LINES FROM ROOF TO GROUND LEVEL.

-

21

Fig. 12.1

©

2014 UMA Solar

«
...
20
21
22
23
24
...
»

Содержание HC-10.5




































Отзывы:

Нет отзывов

Похожие инструкции для HC-10.5

PINT-090T-APL Series

Бренд: ICOP Technology Страницы: 46

Бренд: MEE Страницы: 48

Бренд: ICPDAS Страницы: 8

Бренд: FLIN Страницы: 28

Бренд: Aaeon Страницы: 61

Бренд: Qomo Страницы: 37

Black/White LCD

Бренд: panja Страницы: 50

Бренд: Quanmax Страницы: 34

AMX Modero S Series

Бренд: Harman Страницы: 2

Бренд: Gecko Страницы: 39

CO-100/P2002 Series

Бренд: Cincoze Страницы: 104

Бренд: merten Страницы: 23

CTRLW-DMXB-TW-4Z

Бренд: American Lighting Страницы: 2

Бренд: Acnodes Страницы: 1

Бренд: Turner Designs Страницы: 19

IPPC-6172F Series

Бренд: Advantech Страницы: 88

Бренд: Jung Страницы: 7

Бренд: ELITAL Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды