background image

Recommended Installation Procedures

Mounting the Module

Installing The Antenna 

Connecting The Starter Disable

BEFORE STARTING INSTALLATION

:

- Discuss the optional system features with the customer.
- Take a few minutes to review the installation and owners manuals.
- Do a walk around the vehicle and check for any damage.                 
- If installing a LED discuss the placement with customer before installing.

Never mount the module in the engine compartment. Select a location under the dash 
to install the main module. Be certain that the module is securely attached and does not 
obstruct any serviceable  areas. Mount the module so that it cannot be seen if looking 
under the dash as it could be easily unplugged by a thief. The module must be  free from 
all  moving parts such as brake, clutch and gas pedals linkages.

The antenna should be mounted in the top center of the windshield with the antenna mast
facing downwards. First ensure that the glass is clean and dry, remove the plastic from the
adhesive tape then press against the glass.     

This system contains a built-in Starter disable relay. The brown starter kill  wire from 
the wire harness bag will connect to the module as normally connected. (87a & 30)
Cut the brown wire in half,  then locate the vehicles starter wire. This wire will switch to
12volts in the crank/start position only. Cut this wire in half and confirm that the 
vehicle will not start. Connect the brown wires, one  to each side of the cut starter wire. 
Route the brown wires to the main module and connect.   

This output can be used to activate the interior lights upon disarming the alarm, connect
this output to a relay to activate the interior light. The dome light output will stay active for 
30 seconds upon disarm. 

Recommended Pre-Installation Procedures

Mounting The Siren

Choose a location in the engine compartment that is away from high sources of heat 
and direct exposer to water. The siren should be mounted as well as grounded to solid 
metal. Run the wiring for the siren so that it can not be seen or reached from below the
vehicle.  

PAGE 4

SECURITY SYSTEM

INSTALL GUIDE

Содержание 660 Series













Отзывы: