manualshive.com logo in svg

Ultra-Aire SD12, Руководство по установке

Поделиться
Скачать
Ultra-Aire SD12 Скачать руководство пользователя страница 25

24

25

Ultra-Aire SD12 Installation Instructions

www.Ultra-Aire.com | (800) 533-7533

www.Ultra-Aire.com | (800) 533-7533

Ultra-Aire SD12 Installation Instructions

Fresh air ventilation is optional.
Fresh air may be brought into the structure by connecting an insulated duct from outside the structure to 
the 6" inlet of the Ultra-Aire SD12. A ventilation control is needed to program the time and frequency that  
the unit introduces outside air. The time and frequency of ventilation should be based on the size and  
occupancy of the residence.  
•  The fresh air ventilation duct should be connected to the 6" round collar on the front of the Ultra-Aire 

SD12.  

•  An insulated 6" diameter duct provides up to 100-150 CFM of outside air.  
•  If a motorized damper is not being used, fresh air is controlled by the manual damper in the 6" collar  

of the Ultra-Aire SD12. Performance of the Ultra-Aire SD12 can be impacted by inside and outside air 
conditions.  

•  When a 6" motorized damper is used, a digital control is required.
• It may be necessary to use 8" duct work if additional fresh air is required.
•  In cold climates or at times when the dew point is low, ventilation can be used to dehumidify the  

structure, making the Ultra-Aire SD12 capable of year-round drying. 

FRESH AIR VENTILATION

OUTLET DUCT 

COLLAR WITH 

BACK DRAFT 

DAMPER

RETURN AIR

INLET DUCT

COLLAR

FRESH AIR

INLET DUCT

COLLAR

RETURN AIR

INLET DUCT

COLLAR

FRESH AIR

INLET DUCT

COLLAR

AIR FLOW

Air

Flow

Hot Climate

6" Fresh Air Inlet 

(Optional)
10" Return Air Inlet
10" Supply Air Outlet 

A

B
C

Outdoor Air

30°F, 65%RH

Indoor Air

70°F, 50%RH

Outlet Air

59°F, 51%RH

Cold Climate

A

B

C

6" Fresh Air Inlet 

(Optional)
10" Return Air Inlet
10" Supply Air Outlet 

A

B
C

Mixed Air

59°F

51%RH

Mixed Air

59°F

51%RH

Outdoor Air

90°F, 65%RH

A

Indoor Air

70°F, 50%RH

B

Outlet Air

75°F, 65%RH

C

Mixed Air

75°F

65%RH

Mixed Air

75°F

65%RH

Outdoor Air

30°F, 65%RH

A

Indoor Air

70°F, 50%RH

B

Outlet Air

59°F, 51%RH

C

Mixed Air

59°F

51%RH

Mixed Air

59°F

51%RH

Fresh Air Ventilation With Dehumidifier Off and Fan Only Operation

Outside air mixes with the dehumidifier’s return air before being supplied to the home. Outside  
temperature, inside temperature and relative humidity will impact the combined outlet air conditions.

Note: Temperature and relative humidity may vary depending on duct distribution scheme.

Содержание SD12





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды