background image

3

LONG ROD SERIES ENGINES 130 & 140 CI

Ultima’s Complete Assembled, Unassembled and Long Blocks in the Long Rod Series of Engines have no warranty expressed or implied,
however, engines that are suspect of being defective may qualify for limited warranty assistance. Due to the nature of these engines ultimate
use and performance level we feel it is impossible to express a comprehensive warranty and any claims will be handled strictly at Ultima’s
discretion. 

ENGINE COMPONENTS

All of Ultima’s individual engine components or kits including long blocks, fuel systems and ignition systems are covered by a 12 Month
Warranty. 

This warranty covers part replacement only and no other associated expenses

. In the event that any warranty service is required,

the original purchaser must call or write Midwest Motorcycle Supply immediately with the problem. Many problems can be rectified by a
telephone call and need no further course of action. Merchandise that is suspected of being defective must not be replaced by a Dealer or End
User without prior authorization from Midwest Motorcycle Supply. If it is deemed necessary for Ultima to make an evaluation to determine
whether the part was defective, it must be packaged properly to prevent further damage and be returned prepaid to Midwest Motorcycle
Supply.  You must also include a copy of the original invoice and detailed letter outlining the nature of the problem.  You must also outline how
the part was used and the circumstances at the time of failure. If, after an evaluation has been made by Ultima and the part was found to be
defective, repair to the existing part or replacement will be granted 

at Ultima’s discretion

.

ADDITIONAL WARRANTY PROVISIONS:

1. Ultima

®

shall have no obligation in the event an Ultima

®

part is modified by any other person or organization.

2. Ultima

®

shall have no obligation in the event an Ultima

®

part becomes defective in whole or in part as a result of improper installation,

improper maintenance, improper use, abnormal operation, or any other misuse or mistreatment of the Ultima

®

part.

3. Ultima

®

shall not be liable for any consequential or incidental damage resulting from the failure of an Ultima

®

part, the breach of any

warranties, the failure to deliver, delay in delivery, delivery in non-conforming condition, or for any other breach of contract or duty between
Ultima

®

and a customer.

4. Ultima

®

parts are designed exclusively for use in Harley-Davidson

®

type motorcycles. Ultima

®

shall have no warranty 

or liability obligation if an Ultima

®

part is used in any other application.

Содержание Competition Series









































Отзывы: