CV
1
2
3
4
5
6
7
8
17
18
19
29
33
34
35
36
37
38
39
40
49
Default
3
1
2
2
48
24
3
85
2000
199 / 208
0
6
1
2
4
8
16
32
0
0
32
Table of the CVs (Configuarion Variables)
Description
Address
Minimal speed
Acceleration
The value per increment is 5 ms for a speed change of 1
For an internal speed setting of 200 (CV 5=50 or CV 94=200)
the acceleration will be 1 second
Deceleration (same factor as CV 3)
Maximal speed (must be greater than CV 2)
Intermediate speed
(must be greater than CV 2 and
lesser
than CV 5 )
Version number (The used controller can be updated.)
Manufacturer ID
Extended address
17 = high byte / 18 = low byte
Consist Address (doubleheading)
0 = no consisting
if bit 7=1 direction inversion will occur,
desired CADR + 128 = direction inversion
Configuration per DCC-specification Value
Bit 0=0 Normal direction
0 *
Bit 0=1 Inverted direction
1
Bit 1=0 14 Speed steps 0
Bit 1=1 28 Speed steps
2 *
Bit 2=0 Digital operation only
0
Bit 2=1 automatic analog-/digital recognition
4 *
Bit 3
n/a
-
Bit 4=0 Speed table by CV 2, CV 5, und CV 6
0 *
Bit 4=1 Speed table by CV 67 .. CV 94
16
Bit 5=0 Short address (CV 1)
0 *
Bit 5=1 extended address(CV 17/18) 32
Bit 6/7
n/a
Mapping table for F0 when going forward.
Bit 0
front light
1 *
Bit 1
rear light
2
Bit 2
Ancillary output A1
4
Bit 3
Ancillary output A2
8
Bit 4
Switching (half) speed range
16
Bit 5
Acceleration/Deceleration active
32
Mapping table for F0 when going backwards. See CV 33.
Mapping table for F1. See CV 33
Mapping table for F2. See CV 33
Mapping table for F3. See CV 33
Mapping table for F4. See CV 33
Mapping table for F5. See CV 33
Mapping table for F6. See CV 33
Decoder configuration Value
Bit 0=0 compensation on
0 *
Bit 0=1 compensation off
1
Bit 1
n/a
-
Bit 2=0 decelerate to 0 in braking section
0 *
Bit 2=1 decelerate to speed set in CV 52
4
Bit 3=0 data format DCC and Motorola
0 *
Bit 3=1 data format DCC only
8
Bit 4=0 data format DCC and Motorola
0 *
Bit 4=1 data format Motorola only
16
Bit 5=0 no dimming for A1 and A2
0
Bit 5=1 dimming on for A1 and A2
32 *
Bit 6=0 lamp connection straight
0 *
Bit 6=1 lamp connection swapped
64
Bit 7=0 braking invoked by signal
0 *
Bit 7=1 braking invoked by analog voltage
128
Attention: When both digital formats are inactivated, the decoder will not
respond to any signal and can only be programmed
Range
DCC 1-127
Mot 1-80
1-63
1-63
1-63
1-63
1-63
-
-
1-9999
192-231 / 0-255
1-127
0-255
0-63
0-63
0-63
0-63
0-63
0-63
0-63
0-63
0-255