UFO LUNA SLP-3000M Скачать руководство пользователя страница 12

PROCEDURES

 

FOR

 

ALL

 

MODEL

 

TYPES

Problem

Possible Cause(s)

Remedy

Unit is dead – 

no light output 
and LED power 

indicator on 

PSU is not 

illuminated

Mains supply o

Check supply & reinstate

Loose mains plugs

Check plugs

Plug fuse blown (UK)

Check fuse. If blown, replace

PSU failed

Replace PSU

Unit is dead – 

no light output 
and LED power 

indicator on 

PSU is illumi

­

nated, but LED 

indicator on 

Light source not 

illuminated

PSU failed

Replace PSU

Unit is dead – 

no light output 

but LED power 

indicator is 

illuminated

DMX dimming at minimum 

(for DMX version only)

Adjust brightness on 

controller (increase value up 

from 0)

DMX fault on controller or 

DMX cable

Remove DMX XLR plug from rear of light 

source. Light source wil default to full 

bright. Repair DMX controller 

or cabling.

LED array failure

Replace light source

Unit not 

responding to 

DMX 

commands

Address incorrect

Check the address set on unit matches 

the address set on the controller

DMX cable fault

Refer to manual diagram for correct 

wiring termina

ti

on. Carry out con

ti

nuity 

check.

Swap DMX cable for known 

good cable

Note: 

 please complete relevant troubleshooting procedures before returning the unit to us for 

further investigation.

TROUBLESHOOTING

LUNA

 

SLP

 

USER

 

GUIDE

12

Содержание LUNA SLP-3000M

















Отзывы: