background image

- Output:

- Load impedance:

- Distortion:

- Dimensions:

- Maximum consumption:

- Weight:

- Colour:

- Presentation:

- Passing band:

- Power supply:

- Tone controls:

300 W. RMS at 1 KHz.

16 (L 70 V.).

33 (L 100 V.).

1%.

430x376x140 mm. (3 U).

600 VA.

19.8 Kgs.

Black.

epoxy / metal.

from 50 Hz. to 17 Khz.

230 VAC (50/60 Hz.).

at 100 Hz.

14 dB.

at 10 KHz.

13 dB.

W

W

4 configurable inputs, balanced microphone / auxiliary.

microphone:

sensitivity = 0,7 mV.
impedance = 200 to 600

.

voice equalisation filter = -15 dB at 100 Hz.
phantom alimentation = 12 VDC

1 auxiliary input (remote controlled modulation cut).

sensitivity= 190 mV

impedance= 47 K .

Direct signal input to mixer bus.

sensitivity = 500 mV

impedance = 600 .

Signal output.

level = 800 mV

impedance = 600 .

Insertion.

output = 400 mV / 600

.

input = 400 mV / 4700

.

4

.

8

.

300 W. RMS five-input power amplifier

with built-in mixer,

for professional audio applications.

-Microprocessor-controlled-

auxiliary:

sensitivity = 190 mV.
impedance = 47 K .

Insertion connector for external signal processors.

8 bits control microprocessor.

ON

MOD

OFF

ON

AUX-5

MIC/AUX-4

MIC/AUX-3

MIC/AUX-2

MIC/AUX-1

Digital

F

MASTER

4

3

2

1

5

6

7

8

AX-309

16

1

610.104A

MIXER AMPLIFIER DIGITAL

TECHNICAL CHARACTERISTICS

C/ LUIS I, 88, 3ª planta
28031 - MADRID
ESPAÑA
Tel: 34-91 311 60 76
Fax: 34-91 450 19 97

[email protected]

Madrid

Delegation

Main

Office

Avda. BARCELONA, 24
08970 - SANT JOAN DESPÍ
BARCELONA - ESPAÑA
Tel: 34-93 477 28 54
Fax: 34-93 261 17 52

[email protected]

UDE reserves the right to modify the technical characteristics of its products without previous notice

Содержание AX-309

















Отзывы: