Ublox SARA-R4 Series Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 307

Ublox SARA-R4 Series Скачать руководство пользователя страница 102

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

10 V24 control and V25ter

Page 102 of 307

10.10 Return to on-line data state O

O

SARA-R404M SARA-R410M-01B SARA-R410M-02B SARA-R410M-52B SARA-R412M

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

full

Yes

No

No

-

10.10.1 Description

Causes the DCE to return to online data state and issue a CONNECT or CONNECT <text> (based on

command) intermediate result code on DTE. It is the complementary command to the escape sequence, or to
the other actions (DTR ON to OFF transition, see table in

) that cause the DCE to switch from

online data state to online command state.

ATO command is used to resume both circuit-switched and packet-switched data call. The resume is only
possible if the PPP L2 protocol is used.

10.10.2 Syntax

Type

Syntax

Response

Example

Action

ATO

<response>

ATO

CONNECT

10.10.3 Defined values

Parameter

Type

Description

<response>

String

•

CONNECT

•

NO CARRIER: the online data state cannot be resumed

10.10.4 Notes

• The command provides an error result code ("+CME ERROR: operation not allowed" if

is set to 2)

in the following cases:

o The DCE is not in online command state
o It is issued on a DCE different from the one in online command state

• In case of PSD call, any data from the network (downlink data) received by the DCE during the on-line

command state is discarded. This means that after the O command and on-line data state resume, any
possible data loss has to be recovered by upper layer protocols (e.g. TCP).

10.11 Escape character S2

S2

SARA-R404M SARA-R410M-01B SARA-R410M-02B SARA-R410M-52B SARA-R412M

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

partial

No

No

-

10.11.1 Description

Controls the decimal value of the ASCII character used as the escape character. A value greater than 127
disables the escape process, i.e. no escape character will be recognized. The escape sequence contains three
escape characters e.g. "+++".

10.11.2 Syntax

Type

Syntax

Response

Example

Set

ATS2=<value>

OK

ATS2=43

OK

Read

ATS2?

<value>

043

«
...
100
101
102
103
104
...
»

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов