Ublox MPCI-L2 series Скачать руководство пользователя

Страница: 30 / 158

TOBY-L2 and MPCI-L2 series - System Integration Manual

UBX-13004618 - R07

Advance Information

System description

Page 30 of 158

1.6

System function interfaces

1.6.1

Module power-on

The

PWR_ON

input pin is not available on MPCI-L2 series modules.

When the TOBY-L2 and MPCI-L2 series modules are in the not-powered mode (switched off, i.e. the

VCC

3.3Vaux

module supply is not applied), they can be switched on as following:



Rising edge on the

VCC

3.3Vaux

supply input to a valid voltage for module supply, so that the module

switches on applying a proper

VCC

3.3Vaux

supply within the normal operating range.



Alternately, the

RESET_N

PERST#

pin can be held to the low level during the

VCC

3.3Vaux

rising

edge, so that the module switches on releasing the

RESET_N

PERST#

pin when the

VCC

3.3Vaux

module supply voltage stabilizes at its proper nominal value within the normal operating range.

The status of the

PWR_ON

input pin of TOBY-L2 modules while applying the

VCC

module supply is not relevant:

during this phase the

PWR_ON

pin can be set high or low by the external circuit.

When the TOBY-L2 modules are in the power-off mode (i.e. switched off with valid

VCC

module supply applied),

they can be switched on as following:



Low level on the

PWR_ON

pin, which is normally set high by an internal pull-up, for a valid time period.



Low level on the

RESET_N

pin, which is normally set high by an internal pull-up, for a valid time period.



RTC alarm, i.e. pre-programmed alarm by AT+CALA command (see

u-blox AT Commands Manual

[3]).

As described in Figure 13, the TOBY-L2 series

PWR_ON

input is equipped with an internal active pull-up resistor

to the

VCC

module supply: the

PWR_ON

input voltage thresholds are different from the other generic digital

interfaces. Detailed electrical characteristics are described in

TOBY-L2 series Data Sheet

[1].

Baseband

Processor

PWR_ON

TOBY-L2 series

VCC

Power-on

Power

Management

Power-on

50k

Figure 13: TOBY-L2 series PWR_ON input description

Содержание MPCI-L2 series































































































































































Результаты поиска

Содержание MPCI-L2 series

Отзывы:

Похожие инструкции для MPCI-L2 series

Бренды по названию

Популярные бренды

Ublox MPCI-L2 series, Руководство по системной интеграции

Результаты поиска

Содержание MPCI-L2 series

Отзывы:

Похожие инструкции для MPCI-L2 series

Бренды по названию

Популярные бренды