Ublox MPCI-L2 series страница 157 Скачать руководство пользователя | Manualshive

Страница: 157 / 158

background image

TOBY-L2 and MPCI-L2 series - System Integration Manual

UBX-13004618 - R07

Advance Information

Revision history

Page 157 of 158

Revision history

Revision

Date

Name

Status / Comments

R01

20-Dec-2013

sses

Initial release for TOBY-L2 series

R02

21-Mar-2014

sses

Initial release including MPCI-L2 series
UART and GPIOs remarked as not supported by TOBY-L2x0-00S

R03

23-Jul-2014

sses

Advance Information document status
Updated MPCI-L2 descriptions
Updated USB description and design-in, including VUSB_DET pin previously RSVD
Updated MPCI-L2 thickness and installation guidelines
Updated MPCI-L2 power-off procedure
Updated MPCI-L2 pins 3, 5, 44, 46 definition: Not Connected instead of GPI/GPO
Updated GPIOs definition and description
Additional design-in examples, minor corrections and improvements

R04

30-Sep-2014

lpah

Updated FW version for Engineering Samples
Additional design-in and minor corrections

R05

28-Nov-2014

lpah / sses

Changed status to Early Production Information
Updated VUSB_DET description and application circuits: the VUSB_DET functionality is
not supported, and the pin should be left unconnected or it should not be driven high
Added maximum antenna gain requirements as per FCC RF radiation exposure limits
Corrected MPCI-L2 pinout
Additional design-in and minor corrections

R06

28-Jan-2015

sses

Added description and design-in for TOBY-L2xx-50S, i.e. the “50” product version:
updated UART, SDIO, GPIO sections

R07

29-May-2015

sses

Added description and design-in for TOBY-L280-00S and TOBY-L201-01S:
updated UART, FTP, HTTP, FOTA sections and any other applicable section

«
...
155
156
157
158
»

Содержание MPCI-L2 series































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPCI-L2 series

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Union Instruments Страницы: 63

Бренд: B&G Страницы: 19

Бренд: IBM Страницы: 214

Бренд: STIEBEL ELTRON Страницы: 44

Бренд: Seiko Страницы: 30

ASC G Wi-Fi kit

Бренд: Waeco Страницы: 386

Бренд: u-blox Страницы: 157

Бренд: Airlow Страницы: 20

TOP-43 EE Series

Бренд: CAME Страницы: 2

Бренд: WattMaster Страницы: 104

Бренд: UMAX Technologies Страницы: 54

Бренд: Mandik Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды