Ublox MAX-M10 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 92

Ublox MAX-M10 Скачать руководство пользователя страница 69

MAX-M10M - Integration manual

Refer to the MAX-M10M data sheet [

] for RF parameters.

4.3.2 Out-of-band blocking immunity

Out-of-band RF interference may degrade the quality and availability of the navigation solution.
Out-of-band immunity limit describes the maximum power allowed at the receiver RF input with no
degradation in performance. Minor violation of the immunity limit may reduce C/N0 of the received
signals but does not necessarily aﬀect the overall receiver performance. However, a signiﬁcant
violation may reduce receiver sensitivity or cause a complete loss of signal reception. The severity of
the interference depends on the repetition rate, frequency, signal level, modulation, and bandwidth
of the signal.

shows a typical out-of-band immunity level for the MAX-M10M RF input. The internal LNA

is in normal-gain mode (default). The measurement is done at room temperature using a test signal
with 64QAM modulation and 10 MHz bandwidth similar to an LTE signal.

If the out-of-band immunity limit is exceeded, it is recommended to verify that the receiver
performance is not aﬀected or is at an acceptable level in the presence of interference.

Figure 26: MAX-M10M out-of-band immunity level at 400 - 1460 MHz and 1710 - 3300 MHz for the normal-gain mode
(default). Preliminary data subject to change.

shows tabulated values for out-of-band immunity at selected cellular and Wi-Fi

frequencies.

Parameter

Frequency (MHz)

699

785

915

1710

1880

1980

2350

2440

2690

UBX-22038241 - R02

4 Hardware integration

Page 69 of 92

C1-Public

«
...
67
68
69
70
71
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды