background image

 

EVK-M8T - User Guide 

UBX-14041540 - R05 

 

Page 2 of 22 

Early Production Information 

 

 

Document Information 

Title 

EVK-M8T 

Subtitle 

User Guide 

Document type 

User Guide 

Document number 

UBX-14041540 

 

Revision and date 

R05 

20-May-2018 

Document status 

Early Production Information 

 

This document applies to the following products: 

Product name 

Type number 

Hardware version 

ROM/FLASH version 

PCN reference 

EVK-M8T 

EVK-M8T-0-01 

Flash FW 3.01 TIM 1.10 

UBX-16005636 

 

European Union regulatory compliance 

EVK-M8T complies with all relevant requirements for RED 2014/53/EU. The EVK-M8T Declaration of Conformity (DoC) is 
available at www.u-blox.com under Support --> Product Resources --> Conformity Declaration. 

 

 

 

u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this 
document. Copying, reproduction, modification or disclosure to third parties of this document or any part thereof is only 
permitted with the express written permission of u-blox. 
The information contained herein is provided “as is” and u-blox assumes no liability for its use. No warranty, either express or 
implied, is given, including but not limited to, with respect to the accuracy, correctness, reliability and fitness for a particular 
purpose of the information. This document may be revised by u-blox at any time without notice. For the most recent 
documents, visit www.u-blox.com.  
Copyright © u-blox AG. 

Содержание EVK-M8T-0-01























Отзывы: