Ubiquiti AF-3G26-S45 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 24

background image

Introduction

Thank you for purchasing the Ubiquiti Networks® 3 GHz, 26 dBi
Slant 45 Polarity Antenna for airFiber®. This Quick Start Guide
is designed to guide you through installation and also includes
warranty terms.

Package Contents

Dish Reflector

Antenna Feed

Mounting Bracket

Protective

Shroud

Pole Clamps

(Qty. 2)

Stabilizer Brackets

(Qty. 2)

RF Cables

(Qty. 2)

Elevation Rod Assembly

M10x150 Carriage Bolts

(Qty. 4)

M10x100 Carriage Bolts

(Qty. 2)

3 GHz, 26 dBi Slant 45

Antenna for airFiber®
Model: AF-3G26-S45

M10x25 Carriage Bolts

(Qty. 3)

M4 Bolts

(Qty. 4)

Quick Start

Guide

Products may be different from pictures and are subject to change without notice.

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable is
designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.

«
1
2
3
4
...
»

Содержание AF-3G26-S45

























Отзывы:

Нет отзывов

Похожие инструкции для AF-3G26-S45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды